• 
    

    
    

      99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看

      ?

      Design and simulation for the brake of crane lifting device

      2015-12-19 08:48:22JingyunZHAOXueCHENGQiangLIXiaoheZHAOHenanMechanicalandElectricEngineeringCollegeXinxiang45300ChinaXinxiangLiftingEquipmentFactoryCoLtdXinxiang45300China
      機床與液壓 2015年12期
      關鍵詞:新鄉制動器起重機

      Jing-yun ZHAO,Xue-i CHENG,Qiang LI,Xiao-he ZHAO(Henan Mechanical and Electric Engineering College,Xinxiang 45300,China)(Xinxiang Lifting Equipment Factory Co.,Ltd,Xinxiang 45300,China)

      Design and simulation for the brake of crane lifting device

      Jing-yun ZHAO1*,Xue-1i CHENG1,Qiang LI2,Xiao-he ZHAO1
      (1Henan Mechanical and Electric Engineering College,Xinxiang 453002,China)
      (2Xinxiang Lifting Equipment Factory Co.,Ltd,Xinxiang 453002,China)

      The design and selection of the brake is an important part during the process of bridge crane manufacturing,the position and layout of brake are related to the stable operation and crane safety.In this paper,the basic design parameter is weight of 10 tons bridge crane,the lifting mechanism for dynamic analysis and the mathematical modelsare established andthe rotational inertia of the mathematical model are evaluated.Different layout schemes of the brake are calculated and simulated,the maximum torque brakeis obtained by using Matlab software,and the optimal scheme of the brake design has been analyzed.

      Brake,Crane,Dynamic model

      Hydromechatronics Engineering

      http://jdy.qks.cqut.edu.cn

      E-mail:jdygcyw@126.com

      1 Introduction

      In the process of industrial production,bridge crane is a common machinery used to transport materials in workshop,it is mainly composed ofcart,trolley and lifting mechanism,among themcart and trolleycontrol the crane running,lifting mechanism mainly realizes material lifting.They are the main mechanism of crane,andtheir performance will directly influence the performance of crane.The lifting mechanism is mainly composed of a motor,coupling,reducer,brake,drum,and the corresponding controller,etc.,as shown in Fig.1.

      In the crane's working mechanism,due to the working characteristics of the crane,design and installation of the brake are needed,so as to guarantee safe operation of the crane.In a lifting mechanism,the installed reducer could ensure material hover at any height,the brake of cart and trolley will stop them at a certain time or certain travel.For the crane working in the open air or running on the slopes,the brake will lock the crane function,especially for a simple crane,the brake also has speed regulating role.

      Fig.1 The structure of Iifting mechanism

      Therefore,in order to guarantee the crane fast,efficient,safe and reliable work,the design of brake and type selection become the important step during the design of crane.Since lifting mechanism requires a higher safety coefficient,a single brake safety coefficient will not be smaller than 1.75 and the two brake safety coefficientwill not be less than 1.25.Because the crane brake is a normally closed brake,the brake should be wear automatic compensation device and a manual release device,which will be used to debug repair.

      For hydraulic brake structure as shown in Fig.2,

      *Corresponding author:Jing-yun ZHAO,Associate professor.

      E-mail:hncad@163.com brake friction pair in a group are connected with the fixed frame;the other group are connected with institutions rolling shaft.When the friction pair contact pressure,it will lead to trigger the brake;however,when the friction pair is separated,the brake will release and the mechanism can exercise.

      Fig.2 The structure of hydrauIic brakes

      2 Establish the mathematical model of lifting mechanism

      The design parameters of the 10t bridge crane are shown in Table 1,motor was selected as 11 kW YBZPE built-in brake motor,high speed shaft of the crane used the DYWZB200-30/30 hydraulic brake.Drum shaft adopts BBB50-13.8 band brake and the reducer was chosen as K4SH8 cylindrical gear reducer.

      TabIe1 Lifting mechanism design parameter tabIe

      Establisha quality-spring-quality equivalent model to the input shaft as a benchmark,as shown in Fig.3,J1is the rotational inertia of the motor rotor and the high-speed shaft brake,J2is the rotational inertia of the high-speed shaft brake and equivalent rotational inertia of gear the transformation on the shaft I in reducer;J3is equivalent rotational inertia of drum and promoted weight transformation on the shaft I,J制is the rotational inertia of the DYWZB200-30/30brake. Therefore,it could be evaluated directly by using mathematical method and cannotbe directly calculated by Pro/E software which is used to establish the threedimensional solid model,and the rotational inertia of the rotating components could be automatically evaluated by using the software.

      Fig.3 EquivaIent modeI diagram

      2.1 The rotational inertia calculation of the drum and weight

      The rotational inertia of the drum:

      Where,ρ is the density,ρ=7 850

      The transformed rotational inertia to the motor shaft is:

      J卷=0.004 06 kg·m2

      The transformed rotational inertia of heavy lifting is:

      Where,Q is the weight and the value is 10 t,g is the gravitational acceleration,D is the drum diameter. The transmission ratio is i,the J重conversion to the motor shaft,and the value is as follows:

      2.2 The equivalent rotational inertia automatic calculation of reducer

      Using Pro/E software to draw K4SH line of cylindrical gear reducer each shaft components,rotational inertia of each axis could be calculated separately,the transformed rotational inertia of each gear to the motor shaft are as follows:

      The resistance torque conversion to the input shaft T2=510 N·m;

      The braking torque conversion to the input shaft T= 900 N·m.

      3 Calculation and simulation ofthe brake arrangement in high speed shaft

      Braking torque to the brake 2 and brake 3 at the same time,each bearing 450 N·m braking torque. Mechanical system based on the input shaft,its equivalent model is shown in Fig.4.During the brake process,motor will stall and the braking torque T becomes the resistance torque.

      Fig.4 The equivaIent modeI diagram of high speed shaft braking

      At this time,the system motion differential equations could be established as follows:

      The initial condition is:

      Substituting the value calculated that:

      Runge-Kutta method for solving differential quations:

      The Matlab program was used to solve the above differential equations and the procedure is as follows:

      function zhidong

      clear;clc

      x0=[0;530;0;530;0];

      [t,x]=ode45(@zhidong,[0,0.2],x0);

      plot(t,x)

      function dx=zhidong(t,x)

      dx=[1;x(3);363*x(4)-540*x(2)+172 211;x(5);103*x(2)-1190*x(4)+524434];

      From the Fig.5,it could be seen:

      T12max=510 N·m,T23max=530 N·m

      Fig.5 Time-domain diagram of torque

      4 Calculation and simulation ofthe brake arrangement in low speed shaft

      Braking torque is applied to the drum 3 and themechanical system is based on the input shaft,the equivalent model is shown in Fig.6.The differential equations of motion could be obtained as follows:

      Fig.6 EquivaIentmodeIdiagramofIowspeed shaft braking

      From the above equations,the following could be obtained.

      If the data are substituted,one could obtain the following:

      The solution of the above differential equations are similar to the previous example,and the calculation resultsare shown in Fig.7.

      T12max=1 920 N·m,T23max=3 200 N·m

      Fig.7 The caIcuIation resuIt of Iow speed shaft braking

      If the time characteristic of braking force is considered,the braking time t could not exceed 7 times of the free vibration period.If the braking time is ti, during braking process,the braking torque TT′1could be gradually added.

      Substitute the data into the above equation,the differential equations of motion become:

      The solutions of the above differential equationsare similar to the previous example,and the calculation resultsare is shown in Fig.8.

      Fig.8 The caIcuIation resuIt of Iinear braking torque

      5 Conclusions

      Fortheabove-mentionedthreebrakedesign schemes,set the brakes to the high speed shaft,the brake torque is small and the size of brake is small as well.However,high speed shaft brake due to the shaft I has negative elastic dynamic load T12,the torque by the shaft I could suddenly reverse,so that to make the gear transmission device,due to the existence of the tooth side gap,inevitably impact.

      Set the brakes to the low speed shaft,the braking torque on the output shaft,shaft I,shaft II loading is greater,but it will not reverse.If the braking time is considered,make the system in the process of braking is not sudden loading,but gradually loading.The maximum dynamic load on shaft I and shaft II are small axis,but the braking torque on the output shaft,the transmission ratio of transmission system is i,the braking torque that the output shaft required should be needed.For iT1,the size of brake is larger.

      In order to minimize flywheel torque of brake mounted on a high speed shaft,the lifting mechanism of motor could be started quickly to reach the rated speed.If a brake is arranged in the high speed shaft,the brake should be installed at the end of the reducer shaft,rather than on the motor shaft,to ensure safe and reliable braking.At the same time,in order to make the mechanism compact layout,it should strive to axial size of the smallest.

      Acknowledgements

      This paper is supported by National Natural Science Foundation of China(No.50775155)and the Henan province Education Department science and technology key projectFundation(No.12A460004).

      [1]Zhang Xin,Xu Zili,Luo Xingjian,Zhao Juan.Research on Key Technologies of Interactive Crawler Crane Simulator[J].Computer simulation,2012(11):386-390.

      [2]Deng Qian-wang,Li Xiao,Gao Li-kun.Research and Application of Crane Motion Simulation Technology in Virtual Scene[J].Computer Engineering and Design,2013;34(11):3961-3965.

      [3]Chen Gang,Cui Zhuang-ping,Zeng Yang.Research on Real-time Motion Simulation of Multi-body System Based on Physics Engine[J].Journal of System Simulation,2013:25(Suppl.):167-172.

      起重機起升裝置制動器的設計與仿真

      趙敬云1*,程雪利1,李 強2,趙筱赫1
      1.河南機電高等??茖W(xué)校,河南新鄉 453002
      2.新鄉市起重設備廠有限責任公司,河南新鄉 453002

      制動器的設計與選型是橋式起重機生產過程的重要環節,制動器的位置與布局關系起重機的運行平穩與安全。以10 t橋式起重機為設計對象,對起升機構進行動力學分析,建立了數學模型,計算了數學模型所需的轉動慣量;并對制動器不同布置方案進行了計算與仿真,利用Matlab軟件得到了制動器制動的最大力矩,分析得出了制動器設計的最優方案。

      制動器;起重機;動力模型

      10.3969/j.issn.1001-3881.2015.12.021Document code:A

      TH215

      11 January 2015;revised 13 March 2015;accepted 15 April 2015

      猜你喜歡
      新鄉制動器起重機
      新鄉作品精選
      聲屏世界(2023年15期)2023-10-31 13:41:58
      新鄉醫學院
      單元制動器停放制動不緩解改進
      機電信息(2022年9期)2022-05-07 01:54:11
      鼓式制動器安全隱患排查與消除
      出征新鄉,武漢石化拼了
      由一起自動扶梯制動器失效而引發的思考
      對起重機“制動下滑量”相關檢驗要求的探討
      MYQ型5000t門式起重機簡介
      大型起重機集中潤滑的研究與改善
      盤式制動器制動尖叫CAE分析及其解決方案
      汽車科技(2015年1期)2015-02-28 12:14:42
      404 Not Found

      404 Not Found


      nginx
      景洪市| 奈曼旗| 惠水县| 慈溪市| 通城县| 濮阳县| 临城县| 安仁县| 行唐县| 昌图县| 谢通门县| 新安县| 和顺县| 盐亭县| 富源县| 武平县| 肇州县| 荣成市| 景德镇市| 江永县| 太康县| 邵阳县| 台中市| 江西省| 万山特区| 宜宾县| 陆川县| 玉林市| 龙门县| 永川市| 固原市| 钦州市| 通化市| 县级市| 西青区| 澳门| 上高县| 磐石市| 武山县| 泸水县| 万载县|