趙潔 張茂林 王賀
摘 ?????要:通過實驗研究聚合物濃度、水礦化度、溫度,聚合物分子量、剪切速率等對抗鹽聚合物流變性的影響,總結了它們的影響規律。實驗結果表明:在低剪切速率下抗鹽聚合物較穩定,有利于驅油;抗鹽聚合物受水礦化度影響不大;隨著溫度的升高,抗鹽聚合物的動力黏度變化不大;對于抗鹽聚合物,在任何剪切速率下,分子量大的動力黏度值也大;在低剪切速率(<81 s-1)下,抗鹽聚合物溶液的動力黏度與濃度無線性關系;當較高剪切速率(>81 s-1)下,動力黏度與濃度成線性關系。通過抗鹽聚合物與普通陰離子聚合物的對比研究,得出了抗鹽聚合物更適用于驅油的優點。
關 ?鍵 ?詞:聚合物;流變性;抗鹽聚合物;黏度
中圖分類號:TE 357 ?????文獻標識碼: A ??????文章編號: 1671-0460(2019)01-0009-04
Abstract: The effect of polymer concentration, water salinity, temperature, polymer molecular weight, shear rate and active agent concentration on rheological properties of salt-resistant polymer was studied experimentally, and their influence laws were summarized. The experimental results show that the salt-resistant polymer is stable at low shear rate and is beneficial to oil displacement. The water salinity has little influence on salt-resistant polymer. With the increase of temperature, the dynamic viscosity of salt-resistant polymer has little change. For salt-resistant polymers, at any shear rate, the larger the molecular weight, the higher the dynamic viscosity of the polymer. At low shear rate of less than 81 s-1, the dynamic viscosity of salt-resistant polymer solution has no linear relationship with the concentration. When the shear rate is higher than 81 s-1, the dynamic viscosity has a linear relationship with the concentration. Through the comparative study of salt-resistant polymer and common anionic polymer, it's pointed out that salt-resistant polymer is more suitable for oil displacement.
Key words: Polymer; Rheological property; Salt - resistant polymer; Viscosity
目前進行的上千次聚合物驅礦場試驗,主要集中在砂巖油藏中進行,部分在碳酸巖地層中進行[1,2]。聚合物類型從20世紀60-80年代的聚丙烯酰胺發展到90年代的使用于高溫高鹽油藏的各種類型聚合物;從效果來看,60-80年代初,聚合物一般提高采收率5%左右,而在90年代,一般提高采收率8%以上。然而,高分子量陰離子聚丙烯酰胺作為增稠劑,也存在耐溫性、耐鹽性和抗剪切能力差的缺陷[3-5]。地層溫度升高,鹽濃度增大,以及高剪切作用下的機械降解及熱降解等作用都使HPAM水溶液濃度下降;尤其對超分子量聚丙烯酰胺,這種影響更加明顯[6-8]。在能夠保證地層高溫和高壓下有效工作黏度時,地面低溫下聚合物水溶液的高黏度極不利于聚合物驅液的注入,造成注入壓力高,加劇了聚合物的機械降解,限制了進一步發揮高分子量聚合物的增稠效果[9]。國家在“十五”攻關和“863”計劃中都安排了“耐溫耐鹽聚合物驅的開發與示范工程”項目。因此急需加大力度研究開發性能優良的耐溫抗鹽性聚合物驅劑。
1 ?實驗部分
1.1 ?實驗藥品與儀器
普通聚合物(1 500萬分子量)、抗鹽聚合物(
1 500萬分子量)。
普通聚合物(2 500萬分子量)、抗鹽聚合物(
2 500萬分子量)。
NaCl,Na2SO4,CaCl2,MgCl2,NaHCO3,Na2CO3,分析純,哈爾濱化工化學試劑廠生產。
KCl,分析純,天津市東麗區東大化工廠生產。
JJ-1定時磁力攪拌儀器,0~3 000 r/min。
攪拌桶。
HHS2-6型電熱恒溫水浴鍋,37~100 ℃,佳木斯前進機械廠。
紅外線快速干燥器,上海市吳淞五金廠。
RV—Ⅱ旋轉黏度計,德國制造。