• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Weighted-averaging-based classification of laser-induced breakdown spectroscopy measurements using most informative spectral lines

    2020-01-10 07:40:46EktaSRIVASTAVAHyeminJANGSunghoSHINJangheeCHOISunghoJEONGandEuiseokHWANG
    Plasma Science and Technology 2020年1期

    Ekta SRIVASTAVA, Hyemin JANG, Sungho SHIN, Janghee CHOI,Sungho JEONG and Euiseok HWANG

    1 School of Mechanical Engineering, Gwangju Institute of Science and Technology (GIST), 123 Cheomdangwagi-ro, Buk-gu, Gwangju 61005, Republic of Korea

    2 LG CNS, LG Sciencepark E13, 71, Magokjungang 8-ro, Gangseo-gu, Seoul 07795, Republic of Korea

    3 Smart Manufacturing Technology Group, Korea Institute of Industrial Technology, 89 Yangdaegiro-gil,Seobuk-gu, Cheonan-si, Chungcheongnam-do 31056, Republic of Korea

    Abstract In this study,efficient spectral line selection and weighted-averaging-based processing schemes are proposed for the classification of laser-induced breakdown spectroscopy(LIBS)measurements.For fast on-line classification,a set of representative spectral lines are selected and processed relying on the information metric, instead of the time consuming full spectrum based analysis. The most informative spectral line sets are investigated by the joint mutual information estimation (MIE)evaluated with the Gaussian kernel density, where dominant intensity peaks associated with the concentrated components are not necessarily most valuable for classification. In order to further distinguish the characteristic patterns of the LIBS measured spectrum, two-dimensional spectral images are synthesized through column-wise concatenation of the peaks along with their neighbors.For fast classification while preserving the effect of distinctive peak patterns,column-wise Gaussian weighted averaging is applied to the synthesized images, yielding a favorable trade-off between classification performance and computational complexity. To explore the applicability of the proposed schemes,two applications of alloy classification and skin cancer detection are investigated with the multi-class and binary support vector machines classifiers,respectively.The MIE measures associated with selected spectral lines in both applications show a strong correlation to the actual classification or detection accuracy, which enables to find out meaningful combinations of spectral lines.In addition,the peak patterns of the selected lines and their Gaussian weighted averaging with neighbors of the selected peaks efficiently distinguish different classes of LIBS measured spectrum.

    Keywords: laser-induced breakdown spectroscopy, mutual information, weighted averaging,alloy classification, skin cancer detection(Some figures may appear in colour only in the online journal)

    1. Introduction

    Laser-induced breakdown spectroscopy (LIBS) is an atomic spectroscopy technique [1] which has undergone rapid development as an analytical technique over the past decade because of its several merits[2,3].LIBS measurement has been applied in a variety of fields,such as medical[4,5],environmental[6,7],food [8, 9], agricultural [10], and engineering applications [11].

    As one of the many of the LIBS applications, metal sorting has gained considerable importance in recent years because of its commercial value [12-14]. LIBS has potential to provide accurate qualitative and quantitative analyses of subject matter[15-17].However,LIBS technique may suffer from performance degradation by undesired photonic effects such as the self-absorption [18], matrix effect [19, 20], and shot-to-shot fluctuations [21]. In order to mitigate such nonlinear effect,several algorithmic approaches are proposed like self-absorption corrected normalization [22, 23] and quantitative methods for compensation of matrix effects [24, 25].

    Alternatively, LIBS is also being explored as a surgical tool for elemental analysis of ablated tissues [26-28]. LIBS can provide real-time feedback regarding the elements in an ablated sample [29], called biomarkers, which facilitates identification of malignant lesions from tissue samples[5, 30, 31]. However, the disadvantages of LIBS (for example, shot-to-shot fluctuation of the LIBS signals and the inhomogeneity of the sample and ablation crater sizes)persist for biological LIBS measurements[2].Furthermore,the highdimensional spectrum may be redundant for elemental analysis because typical spectral emissions are sparsely represented,showing only a small number of peaks on the order of magnitude weaker background. Some of the peaks may be noisy and contain no information needed for the quantitative analysis or classification. In regards to fast/online real-time identification of samples,spectral line selection based on PCA results and prior information about constituent elements of each group has been studied to validate the claim that few informative spectral lines can perform well instead of the whole spectrum for analytical tasks like classification [25].Thus, the selection of a small subset of useful spectral lines that are highly correlated to the analysis can be helpful for improving the sorting speed and performance [32, 33].

    In this study, the root means square (rms) normalization scheme is employed for reducing shot-to-shot fluctuation in alloy samples and the spectral line sets of most influential combinations are extracted by the joint mutual information estimate (MIE) [25]. In addition, the section of characteristic spectral lines for cancer detection is also evaluated using joint MIE.Two-dimensional(2D)spectral images and a weightedaveraging-based (WA) spectral line processing schemes are also proposed in this paper for fast on-line classification while taking into account the characteristic peak patterns. These schemes are implemented for two classification applications using LIBS measurements. For the alloy analysis, classification using a multi-class support vector machine (SVM) classifier is performed for sixteen alloys of three different bases.For skin cancer detection, samples from real skin tissue of melanoma-implanted mice are analyzed under various experimental conditions that affect the classification accuracy and classification with a binary SVM classifier is evaluated.Evaluation results in both applications show that the MIE measures associated with selected spectral lines show a strong correlation to the actual classification or detection performance, and Gaussian weighted averaging with neighbors of the selected peaks efficiently distinguishes different classes of LIBS measured spectrum.

    The rest of the paper is organized as follows. Section 2 describes the LIBS experimental setup and characteristics of its measurements along with the background. Section 3 explains the procedure for most informative spectral line selection scheme.Section 4 elaborates the proposed Gaussian weighted averaging approach. Then, section 5 shows evaluation results of proposed schemes for two LIBS-based classification applications. Finally, we present our conclusions in section 6.

    2. Background

    2.1. LIBS experimental setup

    2.1.1. Alloy samples. The proposed scheme was evaluated for three different alloy bases: Al, Cu, and Fe. For Al base alloys,two different NIST[34]Standard Reference Materials(SRMs/CRMs) were used: Al-232/02 and Al-134/05. For the Cu base group,seven kinds of alloy were used:Cu-1107,Cu-1110, Cu-1111, Cu-1112, Cu-1113, Cu-1114 [32], and the Brammer Standard BS110B [35]. Seven alloys were also included in the Fe-base group: Fe-C1137, Fe-1138, Fe-1139,Fe-C1145, Fe-C1173, Fe-C1291, and Fe-C2424. The compositions of the candidate samples listed in table 1 show that, apart from the major content of their bases being Al, Cu, and Fe, there were also variations of the minor content,i.e.Cr,Ni,Si,Zn,Mn,C,Mo,and Mg.As same-base alloys share core elements and other minor elements, their classification is difficult compared to that for different-base alloys.

    A commercial LIBS system(RT250-EC,Applied Spectra Inc.,USA)was used for LIBS measurement of alloy samples(CRM measurement), where a second harmonic Q-switched Nd-YAG laser (top hat profile) of 532 nm wavelength with a pulse width of 5 ns was used to ablate the sample (illustrated in figure 1). The pulse energy was 3.64 mJ with 20.6 J cm?2fluence. Laser spot diameter was fixed as 150 μm. 5×objective lens (LMH-5X-532, 0.13 NA, Thorlabs, USA) was used in this experiment and the laser spot diameter at sample surface was adjusted by varying the distance between the two lenses of the beam expander. The actual spot diameter at sample surface was verified from the diameter of ablation crater produced on silicon wafer at threshold ablation energy.The profile of ablation craters was measured with a scanning confocal microscope. LIBS spectra were collected from ten different locations on each sample and each measurement spot was ablated by 11 shots.Excluding the first shot at each spot as a cleaning pulse.A total of 100 spectra were included in the evaluation for each alloy sample.Plasma emission was collected using two plano-convex collection lens (LA4148,f = 50.2 mm, Thorlabs, USA) placed at 45° and was transmitted to the six-channel CCD spectrometer via an optical fiber bundle (range 187-1045 nm, 12 288 points,0.068 nm resolution)with a gate-width of 1.05 ms and a gate delay of 0.2 μs for which signal to background ratio became maximum, by controlling a delay generator in commercial system. Since actual resolution and spectral range were different for each channel, here spectral resolution was about0.1 nm [25]. Figure 2 shows a typical single-shot spectra for Al-134/05, Cu-1107 and Fe-1137.

    Table 1.Certified concentrations (%) of major and minor components in Fe, Cu, and Al alloys.

    2.1.2. Skin tissue samples. For melanoma analysis,melanoma lesions were induced on the back of three hairless mice. 12 skin tissues including both melanoma and dermis were excised and ultimately one excised tissue sample for each was used for LIBS measurement. The details of melanoma development and LIBS sample preparation have been reported previously [2, 36]. All procedures were approved by the Animal Care and Use Committee of the Gwangju Institute of Science and Technology and performed in accordance with National Institute of Health (NIH)guidelines (GIST-05).

    For the LIBS measurement of melanoma tissue samples, a diode-pumped ytterbium femtosecond (fs) laser (λ = 1030 nm;τ = 500 fs; s-Pulse HP, Amplitude systems) was used with argon as a buffer gas (15 l min?1). The pulse energy was set to 34.8 μJ [36]. An fs laser is more advantageous in generating LIBS plasma from biosamples due to its high intensity. An intensified charge coupled device (ICCD; PI-MAX3, Princeton Instruments, USA) was used to detect the plasma emission(grating = 1200 grooves mm?1,resolution ~0.1 nm,gain = 10).The gate width of the ICCD spectrometer was set to 50 ns with different values of gate delay. Given that the spectral width that can be covered by the ICCD was only about 100 nm, the measurement was repeated while changing the measurement regime over the entire wavelength region,which produced three spectral regions(250-350,350-450,730-830 nm,labeled Bands 1-3, respectively) that had meaningful emission signals. A total of 100 shots for melanoma and dermis samples were obtained for each band.Over these wavelength ranges,the Mg,CN band,Ca,and K signals could be detected. Figure 3 shows a single shot spectra from melanoma and dermis for all three bands with 0 and 20 ns gate delay.

    2.2. Spectrum variability and normalization

    The influence of emission signal fluctuations and the effect of number factors on the laser beam stability(laser pulse energy,repetition rate, delay time, number of laser shots etc) contribute to the variability of LIBS measurements [37-39]. The improvement of signal and the correction of these effects lead to pre-processing of the captured spectrum; hence normalization schemes have been studied [40-42]. Representative schemes like min-max normalization [43], normalization to matrix line considering matrix [44-46], normalization to the total spectral intensity and normalization to the internal standard peak have been studied for quantitative analysis with LIBS captures [47, 48].

    Finding an internal standard consistent for a broad range of samples can be challenging. Thus, the rms normalization instead of the internal standard normalization was employed herein for the mitigation of undesired degradation in alloys of three different bases. Mutual information measures, which will be discussed later, can work as an indicator for normalized performance. The rms normalization is a method of adjusting raw data by dividing the full range of the spectrum by the rms intensity defined as the square root of the arithmetic mean of the squares of the values:

    where xil,denotes the emission intensity at the wavelength index of l, 1 ≤ l ≤L of the ith shot. The obtained rms is equal to the scaled Euclidean norm mentioned in the background and this concept is similar with total energy.Thus,the superiority of the rms normalization, such as the normalization by the total spectral intensity, is caused by the maintenance of the raw spectra pattern, instead of other normalization methods. Moreover, the rms normalization effectively reduces the spectrum fluctuation like normalization with the total spectral intensity [40].

    2.3. Spectral line selection

    Although LIBS spectra are high-dimensional, only a small portion of spectral lines may contain most of the information for quantitative analysis or classification.Appropriate spectral line selection is an important task to enable an accurate and fast analysis with LIBS. Many recent studies on spectral line selection in LIBS actively examined various spectral line selection methods to efficiently extract the information related to analysis [32, 33, 49, 50]. The two representative types of spectral line selection methods are the following: (1) spectral line or range selection for each component of interest based on the National Institute of Standards and Technology(NIST), (2) informative feature extraction based on multivariate data analysis (MVDA) such as principal component analysis (PCA) [25].

    On the other hand, for some applications, spectral line selection is done by experimental identification. The biomarkers can be experimentally identified through visual examination of the obtained spectra and the dominant peaks of those biomarkers are considered as set of selected informative spectral lines.

    3. Joint mutual information estimation (MIE) based spectral line selection

    Most of the information for quantitative analysis or classification in LIBS-captured spectrum focus on a small subset of spectral lines associated with the concentrated components of interest.Therefore,finding the most informative spectral lines is crucial for efficient spectrum processing for classification.However, exhaustively evaluating the classification accuracy for all combinations is infeasible given the large number of spectral lines,even for a finite number of peaks.Instead,joint mutual information is estimated based on Gaussian kernel[51] to measure the information for classification of the spectral lines.The mutual information is a relative measure so is less affected by the variations of LIBS configuration,remaining invariant to the measurement interruptions, as compared to other intensity based measures. The MIE of the individual spectral line, Xl, and the class, Y is given as follows:

    where △lis the step for discretization andis the step for Gaussian assumption approximated at with d = 2 and σ as the average marginal standard deviation. Note that the most informative spectral lines are not necessarily the large individual information measured in equation (2), which are caused by the dependency on the spectral lines. Thus, joint mutual information must be separately evaluated as follows:

    For three spectral lines,

    where

    Similarly, more spectral lines can be jointly evaluated for the joint mutual information measure, while the number of arguments is also limited on account of the complexity.For a larger number of selections, an additional approximation is needed for computational feasibility, as shown below:

    where

    and

    The approximation in equation (9) becomes less accurate as the number of jointly selected spectral lines increases by dropping some conditions, whereas the inequality still holds since additional conditioning reduces mutual information.

    4. Weighted-averaging-based spectral line processing

    4.1. 2D spectral image

    As noted previously, use of high dimensional LIBS spectra for analysis is computationally expensive and may generate defects in the obtained information [52]. The characteristic lines indicate the unique properties of each target and are crucial for acquisition of distinguishing information. Thus,characteristic spectral lines were selected based on joint MIE discussed in section 3 to reduce the number of lines with minor or no information loss. However, this line number is generally too small and the amount of information provided by the selected lines may be insufficient for reliable classification. Therefore, in this study, customized two-dimensional(2D) images synthesized from the spectrum were employed for efficient classification, where not only the selected lines,but also selected peak patterns corresponding to those lines were column-wise concatenated. These images were synthesized based on the selected spectral lines and their neighbors.Hence, a distinguishing feature space was created for classification. It is important to note that spectral image formation reduces the spectral dimensionality while conserving the distinguishing information.

    2D spectral images corresponding to LIBS spectra are given in figure 4 for Al,Cu,and Fe sample measurements.As apparent from the rightmost column, the 2D images for the different bases are well distinguished; this is beneficial for both inter- and intra-class classification. From the steps in figure 4, it is evident that consequential reduction in the dimension of the leftmost column is achieved; the full spectrum is reduced to selected peaks × neighbors and the equivalent spectral image is obtained.

    4.2. Weighted average (WA) using Gaussian weight

    Because of the uncertainty in the raw spectrum,instead of the intensity data of that spectrum, the Lorentzian curve fitted area can be used for classification [53]. In this study, however, the weighted average measure was introduced as an alternative, so as to smoothen the peak response while enhancing the amount of differentiating information.Once the 2D image was synthesized using the selected peaks and their neighbors, their weighted average was taken to reduce the dimension. The weights were obtained by discretizing the Gaussian curve obtained for a range of standard deviation σ values and a fixed mean, which was later normalized so that the sum was 1[54,55].The genie-aided optimum range of σ was selected to achieve the minimum information loss along with accurate classification [56]. A single spectrum can be described as being composed of L random variables on n observations(or spectra),X1,X2,…,Xn;withxil,being the lth intensity measure of spectrum i.Thus,forxil,,if m peaks of L are selected along with their neighbors on either side, the following equation applies:Consequently, for a spectral line and its neighbor, the weighted average is obtained for K different σ values and the results are concatenated.The weights obtained for m selected peaks and their neighbors with respect to the different σ values are given as

    A weighted-average spectral image obtained through weighted averaging of peaks and their neighbors is depicted in figure 5. The differentiating characteristics of the spectral image are well preserved in its weighted average equivalent because of the similarities in the shapes of the peaks and their neighbors, to the Gaussian curve discretized to procure the weights. It is clearly apparent that the weighted averaging in columns two and three of the figure yields concise andcompact representation of the abstracted information from the raw measurement data.

    Table 2.Ranked spectral line sets by MIE for alloy samples.

    5. Results and discussion

    5.1. Evaluation of the spectral line selection

    5.1.1. Alloys samples. Figure 6 plots the rms of the raw intensity, introduced in section 1, of each shot for the 1600 captured spectra, where a large variation was observed considering each base of alloy. By the rms normalization,all the raw spectra were divided by the rms intensity,such that the rms normalized spectrum will have one as its rms.For the internal standard normalization, the spectral line of Fe was used as the internal standard because the Fe component is more consistent than the others, shown in table 1. To demonstrate the performance of the normalization scheme with respect to the reduction of high shot-to-shot variance,the intra-class variance is investigated with the distance between the different classes of same base alloys. Figure 7 shows the intra-class variance of Cu-1107 and Cu-BS110B over 320-340 nm band with the highest peak intensity and the largest variance. As shown in the figure 7, the spectrum normalized by the rms reduced the variance within the classes and increased the difference between Cu-1107 and Cu-BS110B, thus, rms normalization was preferred in this investigation.

    Alternatively,spectral lines selected by jointly evaluating independent and identically distributed(IID)assumed MIE in equation (2) and average relative distance were also investigated for the raw and normalized spectra as shown in figure 8. For most of the peaks showing a large information measure, the rms normalization outperformed the raw estimate, whereas the maximum intensity estimates were degraded, showing that the classification information was lost. Internal standard estimates were degraded or improved compared to the raw estimate and did not outperform the rms normalization. Furthermore, the improved information measure indicated that rms normalization can mitigate the undesired effects of emission signal fluctuations for an accurate inter- and intra-base alloy classification.

    From the high-dimensional LIBS spectrum, most informative spectral line sets for alloy classification are extracted by three steps: (1) select the candidate peaks by the simple threshold (2) select informative peaks based on IID-MIE; (3)select the set of most informative peaks based on joint MIE.A total of 250 peaks were first selected and 45 peaks were selected based on IID-MIE with the average relative distance between each class as illustrated in figure 9. The set of the most influential combinations among the candidate peaks was extracted by examining the joint MIE based on the Gaussian kernel.Table 2 shows the ranked spectral lines by IID mutual information, and the most informative set of three spectral lines. Elements associated with the respective spectral lines have also been mentioned in the table. Note that the informative set with respect to the larger joint MIE was not always composed of high ranks in the IID analysis.When we add a peak one by one for the set and choose the complementary line that contains more information, the new information that previous lines do not have is preferred.Also,most informative lines selected using mutual information may or may not comprise of persistent resonant lines for an element. Cases where these are present simply substantiate the relevance of the information contained in them through MIE based measure.

    5.1.2. Skin tissue samples. Three different wavelength bands, 250-350 (Band 1), 350-450 (Band 2), and 730-830 nm (Band 3) were used for analysis. As the experimental conditions varied during recording of these samples,the measurements were further divided into those for two different gate delays(0 and 20 ns).In the view of the fact that spectrum for all the three bands varies widely, the line selection mechanism was applied separately for each band.Steps defined in line selection for alloys sample in section 5.1.1 remained the same. A total of 68, 133 and 51 peaks were first selected and 27, 47 and 14 peaks were selected based on IID-MIE with the average relative distance between the classes for Band 1, Band 2 and Band 3 respectively(illustrated in figure 10). Set of lines with highest IID-MIE showing high classification accuracy were different for each band (discussed in the next section). Table 3 shows the ranked spectral lines by IID mutual information,and the most informative set of three spectral lines corresponding to each band. Elements associated with the selected spectral line are the same as that of experimentally identified biomarkers justifying the efficacy of MIE based selection approach [2].Note that similar to what was observed in case of alloys samples, informative set with respect to the larger joint MIE was not always composed of high ranks in the IID analysis.

    5.2. Weighted averaging based classification

    Table 3.Ranked spectral line sets by MIE for skin tissue samples.

    5.2.1. Alloys samples. Of 12 288 spectral lines constituting the full spectrum for the alloy classification experiment, sets of three most informative lines and its information metric were evaluated in the previous section. For all the 3 line sets obtained, to incorporate the peak neighbors, four lines on either side of each peak were selected. Again, the number of peaks on the neighboring side was heuristically selected.Then, each spectrum was narrowed down to a total of 27(=3 × 9) spectral lines. Corresponding to each spectral image, five respective weighted averages for five different σ values were considered, yielding vectors of 1 × 3, which were concatenated to form a 5 × 3 2D image for each spectrum.The normalized Gaussian weights for the chosen σ range are almost coincident with the shapes of the selected peaks and their neighbors. Joint MIE was then again evaluated for these weighted averaged set of most informative spectral lines and set with highest information metric was selected for further analysis. To visualize the distinguishing factors of the synthesized image,the root mean square normalized mean intensities of the selected spectral lines for the three different alloy bases are shown in figure 11.It is apparent that the intensities of the selected spectral lines vary widely depending upon the alloy base. For instance, the normalized intensities of the peaks vary for respective alloys.This variation proves that image synthesis can enhance the differences among the alloy classes as it covers the variation because of addition of neighboring peaks. Using the entire spectrum implicates that correlation among the spectral lines is high which degrades the classification accuracy. On the other hand, using just 3 most informative weighted averaged spectral lines lower the correlation and improve the accuracy.

    Figure 12 depicts the IID and joint MIE evaluated for selected 45 peaks with SVM based classification accuracy.The joint MIE was increased by adding the peak one by one.The larger the joint MIE of the set, the higher the classification accuracy. The sets containing 334.47 nm,324.73 nm with the highest IID MIE shows the higher classification accuracy. The classification results were compared to the full spectrum-bases test and the dominant peaks based test to ensure that the selected set was actually more highly correlated in classifying alloys.The classification losses were recorded for different feature spaces constructed based on prior information and information metric. The classification accuracies were evaluated using 10 fold cross validation with randomly assigned 90% training and 10%testing using an SVM; this was repeated 100 times. The resulting classification accuracy of the most informative weighted averaged spectral lines with rms normalization was 97.81%, which was better than using only 3 MIE based selected lines giving 93.19%accuracy and also outperforming the result with 12 288 full points showing 94.87% and dominant peaks showing 91.69%in the table 4.The proposed weighted average scheme was shown to perform well for inter-and intra-base classification of alloys.The trade-off that occurs between the loss and complexity for only 3 weighted average peaks for multiple standard deviations compared to use of all spectral lines is due to the dimensionality reduction.In the context of inter-base alloy classification, the loss is significantly lower when the alloy composition is varied.

    Table 4.Classification result of 1600 samples based on WA and MIE.

    5.2.2. Skin tissue sample. Since the lines selection mechanism was applied separately on all three bands, classification analysis was also done separately. For the sets of three spectral lines selected using MIE evaluation, ten spectral lines on either side were selected; thus, the customized spectral images for the skin sample were 21 × 3 images for Bands 1-3. Once the spectral image was created for each band, the weighted average corresponding to σ{1, 3, …, 19} was created, yielding a 10 × 3 image for each band corresponding to 10 σ values.Information metric was obtained using joint MIE for these weighted averaged spectral lines and set of line with highest MIE score was selected for each band for further classification analysis.The melanoma and dermis spectra changed with the gate delay;thus, the loss rate also varied depending on the gate delay.

    The standardized mean distance square measure (ζ) is expressed as where μmand σmare the mean and standard deviations of the melanoma samples,respectively, and μdand σdare the mean and standard deviations of the dermis samples, respectively.Comparison of ζRand ζW, which were calculated for a raw sample and for a sample with a weighted average spectral line, respectively, (figure 13) shows that considerably greater differences between the two classes were obtained for the weighted averaged case. This indicates that the weighted average processing scheme is suitable for use in classification applications.

    Figure 14 shows the measurement behavior with respect to increased σ.For the initial σ values,the distance between classes(in this case,the melanoma and dermis)tended to increase.This corresponded to improved classification accuracy as most of the deviations around the neighbors are covered. With increased σ,the distance either remained constant or decreased. This is because a broadened σ spans a wider variation of the neighborhood, which does not contain any differentiating information. Principal component analysis (PCA) of the raw spectral lines and weighted averaged lines,as shown in figure 15,provided further evidence that the proposed scheme achieves better distinction between the two classes than the raw data, as the first principal component covered more variation in the weighted averaged line case.To demonstrate the efficacy of the lines selection mechanism based on joint MIE, classification accuracy was compared for each stage of line selection in figure 16.Weighted averaging of the set of lines selected using information metric outperforms the previously selected line sets in terms of classification accuracy with the expected increase in the MIE score. Finally, the bar graph in figure 17 summarizes the classification losses for all bands and the different delays when (i) all spectral lines, (ii) the experimentally selected spectral lines, (iii) set of three lines selected using joint mutual information measure, and (iv) the weighted average of set of three lines selected using MIE (for different σ values for the weights) were used. As illustrated, the spectral lines corresponding to the higher MIE score contain most of the information,and the Gaussian averaging with additional sides of the peaks provides potential improvement in accuracy with reduced complexity. Considering Band 1, for a 0 ns gate delay, it can be observed that classification loss improves significantly from 7.5% to 2% while reducing the dimension of the feature used from 1024 raw spectral lines(all peaks)to 3 weighted averaged spectral lines for 10 standard deviations of weights (WA with range of sigma). Furthermore, for a delay of 20 ns, the loss improves from 12%to 7.5%while using just 3 weighted average spectral lines for range of sigma. Similar patterns can be observed for the rest of the bands and associated delays.

    6. Conclusion

    The proposed spectral line selection and processing schemes for LIBS systems enable fast and reliable classifications by using only a few but most informative spectral lines,compared to the conventional schemes either using the full spectral range or dominant peaks associated with the concentrated components.The sets of the most influential combinations of spectral lines are extracted by examining the joint mutual information estimate(MIE), which shows improved classification accuracy through the SVM tests. The 2D spectral images and the weighted averaging feature scheme for LIBS-based classification presented here provides a favorable trade-off between complexity and performance. For the case of alloys, the classification loss was found to improve for both intra- and inter-base classifications. Compared to the analysis of the entire spectrum, consideration of selected crucial lines captured less-vulnerable information,which could be further augmented by incorporating the lines neighboring the selected lines. Use of the weighted averaging scheme further reduced the dimensions of the training and test data with only marginal performance degradation.Similarly,in the case of skin cancer detection,the distinguishing factors were further improved through the use of weighted averaging of most informative spectral lines selected using joint MIE, as the distance between the two classes was further increased.Overall,the proposed schemes are highly efficient for LIBS-based classification in terms of both accuracy and computational cost.The simplified features can be easily applied for broader applications of machine learning based classifications over the large dimensional measurements like LIBS. The weighted averaging method can be further refined by considering other peak shapes than Gaussian, depending on the target applications,as subtle difference can be effective when they are combined with the measure like MIE, and have a potential to improve classification accuracy. For additional improvement,transfer learning approach can be employed for simultaneously updating the model as well by tracking the changes in LIBS measurements over time.

    Acknowledgments

    This study was supported by the R&D Center for Valuable Recycling (Global-Top R&D Program) of the Ministry of Environment (Project No. 2016002250003).

    ORCID iDs

    www.www免费av| 亚洲精品国产精品久久久不卡| 精品久久久久久成人av| 桃色一区二区三区在线观看| 国产97色在线日韩免费| av福利片在线| 黄色片一级片一级黄色片| 黄色片一级片一级黄色片| 国产精品亚洲av一区麻豆| 日韩欧美在线二视频| 国产1区2区3区精品| 国产精品野战在线观看| 国产亚洲精品一区二区www| 香蕉久久夜色| 夜夜看夜夜爽夜夜摸| 男人舔女人的私密视频| 亚洲精品一区av在线观看| 夜夜躁狠狠躁天天躁| 成人亚洲精品av一区二区| 88av欧美| 日本免费a在线| 高清毛片免费观看视频网站| 在线观看美女被高潮喷水网站 | 成熟少妇高潮喷水视频| 精品久久久久久久久久免费视频| 国产成人精品无人区| 免费电影在线观看免费观看| 91av网站免费观看| 欧美精品亚洲一区二区| 非洲黑人性xxxx精品又粗又长| 狂野欧美白嫩少妇大欣赏| 亚洲一区高清亚洲精品| 丁香六月欧美| 在线观看66精品国产| 9191精品国产免费久久| 色老头精品视频在线观看| 日本在线视频免费播放| 一卡2卡三卡四卡精品乱码亚洲| 又大又爽又粗| 后天国语完整版免费观看| 香蕉丝袜av| 国产三级黄色录像| 成人手机av| tocl精华| 亚洲成av人片免费观看| 午夜成年电影在线免费观看| 亚洲va日本ⅴa欧美va伊人久久| 搡老熟女国产l中国老女人| 女警被强在线播放| 欧美中文日本在线观看视频| 母亲3免费完整高清在线观看| 中亚洲国语对白在线视频| 亚洲黑人精品在线| 少妇裸体淫交视频免费看高清 | 少妇粗大呻吟视频| 亚洲一区中文字幕在线| 夜夜看夜夜爽夜夜摸| 怎么达到女性高潮| 亚洲七黄色美女视频| 国内精品久久久久精免费| 长腿黑丝高跟| 18禁国产床啪视频网站| 婷婷六月久久综合丁香| 亚洲精品在线美女| 色av中文字幕| 黄色视频,在线免费观看| 三级男女做爰猛烈吃奶摸视频| 天堂影院成人在线观看| 亚洲国产高清在线一区二区三| 成人午夜高清在线视频| 精品少妇一区二区三区视频日本电影| 久久久久免费精品人妻一区二区| 久久这里只有精品中国| e午夜精品久久久久久久| 麻豆国产av国片精品| 午夜免费激情av| 久久中文看片网| 久久亚洲精品不卡| 日韩欧美在线乱码| 一级毛片高清免费大全| 99国产精品99久久久久| 欧美一区二区国产精品久久精品 | 两个人免费观看高清视频| 听说在线观看完整版免费高清| 国产私拍福利视频在线观看| 老鸭窝网址在线观看| 一个人免费在线观看的高清视频| 国产精品久久久久久精品电影| 国产午夜精品论理片| 亚洲天堂国产精品一区在线| 天堂影院成人在线观看| 很黄的视频免费| 欧美日韩一级在线毛片| 国产久久久一区二区三区| a级毛片在线看网站| 国产精品 国内视频| 欧美成人性av电影在线观看| 久久草成人影院| 我要搜黄色片| 国产精品,欧美在线| 国产一区二区三区视频了| 精品熟女少妇八av免费久了| 日韩欧美三级三区| 亚洲一码二码三码区别大吗| 国产精品一区二区三区四区久久| 好男人电影高清在线观看| 国产又色又爽无遮挡免费看| 床上黄色一级片| 久久久久九九精品影院| 久久婷婷人人爽人人干人人爱| 免费看a级黄色片| 此物有八面人人有两片| 亚洲国产欧洲综合997久久,| 欧美性猛交黑人性爽| 最近最新免费中文字幕在线| 久久午夜亚洲精品久久| 精品午夜福利视频在线观看一区| 91在线观看av| 在线国产一区二区在线| 久久久久久久久中文| 成人av一区二区三区在线看| 一区二区三区国产精品乱码| 女人被狂操c到高潮| 色综合站精品国产| 午夜精品久久久久久毛片777| 18美女黄网站色大片免费观看| 九九热线精品视视频播放| 午夜日韩欧美国产| 久久人妻av系列| 午夜福利在线观看吧| 成人一区二区视频在线观看| 黑人巨大精品欧美一区二区mp4| 一级黄色大片毛片| 伦理电影免费视频| 欧美最黄视频在线播放免费| 人妻夜夜爽99麻豆av| 精华霜和精华液先用哪个| av福利片在线观看| 午夜a级毛片| 亚洲精品美女久久av网站| 成人午夜高清在线视频| 最新在线观看一区二区三区| x7x7x7水蜜桃| 久久久国产欧美日韩av| 1024手机看黄色片| 巨乳人妻的诱惑在线观看| 在线观看一区二区三区| 免费看a级黄色片| 成人三级做爰电影| 成年免费大片在线观看| 可以免费在线观看a视频的电影网站| 日韩av在线大香蕉| 日韩三级视频一区二区三区| 欧美黄色片欧美黄色片| 亚洲乱码一区二区免费版| 午夜福利欧美成人| 中文字幕人成人乱码亚洲影| 99久久精品热视频| 亚洲熟妇熟女久久| 欧美成狂野欧美在线观看| 免费在线观看成人毛片| 看片在线看免费视频| 国产亚洲精品av在线| 999久久久精品免费观看国产| 亚洲美女视频黄频| 久久人妻福利社区极品人妻图片| 亚洲一码二码三码区别大吗| 亚洲欧美激情综合另类| 日日爽夜夜爽网站| 久久久久亚洲av毛片大全| 哪里可以看免费的av片| 亚洲av第一区精品v没综合| 日本一二三区视频观看| 老司机午夜十八禁免费视频| 亚洲国产中文字幕在线视频| 又黄又爽又免费观看的视频| 亚洲国产精品合色在线| 亚洲国产欧美人成| 亚洲熟妇熟女久久| 亚洲色图 男人天堂 中文字幕| 色av中文字幕| 成人一区二区视频在线观看| 国产亚洲欧美98| 国产在线精品亚洲第一网站| 亚洲一区中文字幕在线| 一进一出好大好爽视频| 老鸭窝网址在线观看| 成年免费大片在线观看| 高潮久久久久久久久久久不卡| 国产亚洲av高清不卡| 亚洲国产精品sss在线观看| 国产av不卡久久| 一本一本综合久久| 亚洲av中文字字幕乱码综合| 久久久久久九九精品二区国产 | 精品国产美女av久久久久小说| 啦啦啦免费观看视频1| 最近视频中文字幕2019在线8| 国产精品美女特级片免费视频播放器 | а√天堂www在线а√下载| 亚洲av成人av| 免费人成视频x8x8入口观看| 1024视频免费在线观看| 国产片内射在线| 精品无人区乱码1区二区| 欧美国产日韩亚洲一区| 日韩中文字幕欧美一区二区| 欧美日本亚洲视频在线播放| 国产一区在线观看成人免费| 色噜噜av男人的天堂激情| 18禁观看日本| 婷婷六月久久综合丁香| 国产精品一及| 久久久国产欧美日韩av| 国产蜜桃级精品一区二区三区| 日韩欧美 国产精品| 1024香蕉在线观看| 精品欧美国产一区二区三| 日韩欧美在线二视频| 国产69精品久久久久777片 | 国产成年人精品一区二区| 亚洲精品粉嫩美女一区| 最近最新免费中文字幕在线| 日本精品一区二区三区蜜桃| 免费在线观看黄色视频的| 高潮久久久久久久久久久不卡| 久久 成人 亚洲| 亚洲成人久久性| 波多野结衣高清作品| 真人一进一出gif抽搐免费| 亚洲国产中文字幕在线视频| 一本大道久久a久久精品| 免费在线观看黄色视频的| 人妻丰满熟妇av一区二区三区| 白带黄色成豆腐渣| 日韩欧美三级三区| svipshipincom国产片| 精品国产超薄肉色丝袜足j| 久久精品国产亚洲av香蕉五月| 亚洲aⅴ乱码一区二区在线播放 | 很黄的视频免费| 国产探花在线观看一区二区| 精品欧美国产一区二区三| 免费观看人在逋| a级毛片a级免费在线| 麻豆国产av国片精品| 亚洲人成网站高清观看| netflix在线观看网站| 国产爱豆传媒在线观看 | 一本大道久久a久久精品| 黑人欧美特级aaaaaa片| 嫩草影院精品99| 亚洲国产欧洲综合997久久,| 欧美午夜高清在线| 国产免费男女视频| 久久午夜综合久久蜜桃| 国产亚洲精品久久久久久毛片| 亚洲精品中文字幕在线视频| 久久精品人妻少妇| 日本a在线网址| 亚洲欧洲精品一区二区精品久久久| 欧美高清成人免费视频www| 亚洲真实伦在线观看| 久久人妻福利社区极品人妻图片| 又爽又黄无遮挡网站| 精品第一国产精品| 久久精品国产综合久久久| 2021天堂中文幕一二区在线观| 亚洲精品一区av在线观看| 欧美日韩精品网址| 97碰自拍视频| 看黄色毛片网站| 午夜视频精品福利| 午夜福利免费观看在线| 久久久国产成人精品二区| 国产精品国产高清国产av| 搡老岳熟女国产| 日本免费一区二区三区高清不卡| 国产欧美日韩精品亚洲av| 亚洲精华国产精华精| 狠狠狠狠99中文字幕| 国产精品久久电影中文字幕| 女同久久另类99精品国产91| 床上黄色一级片| 久9热在线精品视频| 真人做人爱边吃奶动态| 国产不卡一卡二| 久久天躁狠狠躁夜夜2o2o| 亚洲一卡2卡3卡4卡5卡精品中文| 亚洲av成人一区二区三| 国产激情欧美一区二区| 精品午夜福利视频在线观看一区| 国产成人啪精品午夜网站| 中文在线观看免费www的网站 | 一二三四在线观看免费中文在| 老司机靠b影院| av有码第一页| 久久精品91无色码中文字幕| 淫秽高清视频在线观看| 这个男人来自地球电影免费观看| 亚洲av日韩精品久久久久久密| 免费电影在线观看免费观看| 国产精品自产拍在线观看55亚洲| 国产欧美日韩一区二区精品| 亚洲精品国产精品久久久不卡| 欧美成人一区二区免费高清观看 | 日本一二三区视频观看| 久热爱精品视频在线9| 不卡av一区二区三区| 两个人看的免费小视频| 亚洲精品一卡2卡三卡4卡5卡| 精品久久久久久,| 亚洲男人天堂网一区| 亚洲一码二码三码区别大吗| 99久久国产精品久久久| 美女扒开内裤让男人捅视频| 一区二区三区国产精品乱码| 日韩中文字幕欧美一区二区| 精华霜和精华液先用哪个| 亚洲av成人av| 欧美zozozo另类| 日本一二三区视频观看| 制服人妻中文乱码| 不卡一级毛片| 久久香蕉国产精品| 一二三四在线观看免费中文在| 精品久久久久久久久久免费视频| 免费在线观看日本一区| 久热爱精品视频在线9| tocl精华| 日本免费a在线| 毛片女人毛片| 亚洲欧美精品综合久久99| 高潮久久久久久久久久久不卡| 亚洲av五月六月丁香网| 午夜日韩欧美国产| 天堂影院成人在线观看| 国产亚洲精品av在线| 国产伦在线观看视频一区| 欧美精品啪啪一区二区三区| 又黄又爽又免费观看的视频| 亚洲国产高清在线一区二区三| 亚洲人成网站在线播放欧美日韩| 亚洲电影在线观看av| 又粗又爽又猛毛片免费看| 亚洲成人精品中文字幕电影| 88av欧美| 18禁美女被吸乳视频| 成人手机av| 欧美日韩福利视频一区二区| 久久久精品国产亚洲av高清涩受| 精品久久久久久久久久久久久| 淫妇啪啪啪对白视频| 国产99久久九九免费精品| 亚洲国产精品合色在线| 国产午夜福利久久久久久| 国产不卡一卡二| 一二三四社区在线视频社区8| 狠狠狠狠99中文字幕| 久久性视频一级片| 日本精品一区二区三区蜜桃| www日本黄色视频网| 五月玫瑰六月丁香| 午夜福利视频1000在线观看| 亚洲五月婷婷丁香| 成人av在线播放网站| 狂野欧美激情性xxxx| 国产午夜精品论理片| 日韩精品青青久久久久久| 97人妻精品一区二区三区麻豆| 国产精品免费一区二区三区在线| 国产av一区二区精品久久| 视频区欧美日本亚洲| 久久亚洲真实| 久久草成人影院| 特大巨黑吊av在线直播| 成人亚洲精品av一区二区| 日日爽夜夜爽网站| 国产午夜精品论理片| 日本免费一区二区三区高清不卡| 国产真人三级小视频在线观看| 国产精品,欧美在线| 亚洲avbb在线观看| 一卡2卡三卡四卡精品乱码亚洲| www.999成人在线观看| 国产精品久久视频播放| 日韩欧美国产在线观看| 国内少妇人妻偷人精品xxx网站 | 美女免费视频网站| 免费人成视频x8x8入口观看| 欧美久久黑人一区二区| 一级黄色大片毛片| 久久久国产精品麻豆| 亚洲avbb在线观看| 12—13女人毛片做爰片一| 大型av网站在线播放| 国产激情偷乱视频一区二区| 午夜福利18| 在线观看免费日韩欧美大片| 精品久久久久久久久久免费视频| 亚洲专区字幕在线| 久久精品夜夜夜夜夜久久蜜豆 | 欧美一级a爱片免费观看看 | 又大又爽又粗| 精品一区二区三区av网在线观看| 五月伊人婷婷丁香| 麻豆国产av国片精品| 成年版毛片免费区| 琪琪午夜伦伦电影理论片6080| 免费在线观看黄色视频的| 亚洲最大成人中文| 88av欧美| 国产成人一区二区三区免费视频网站| 亚洲国产精品合色在线| 99在线人妻在线中文字幕| 久久久久九九精品影院| 国产亚洲精品一区二区www| 国产91精品成人一区二区三区| 99热6这里只有精品| 国产99白浆流出| 亚洲一码二码三码区别大吗| 亚洲国产日韩欧美精品在线观看 | 可以免费在线观看a视频的电影网站| 国产亚洲av高清不卡| 国产精品爽爽va在线观看网站| 国产高清videossex| 一级a爱片免费观看的视频| 18禁美女被吸乳视频| 50天的宝宝边吃奶边哭怎么回事| 岛国视频午夜一区免费看| 母亲3免费完整高清在线观看| 日韩大尺度精品在线看网址| 午夜免费观看网址| 国产日本99.免费观看| 国产伦一二天堂av在线观看| 成人三级黄色视频| tocl精华| 熟妇人妻久久中文字幕3abv| 亚洲,欧美精品.| 精品一区二区三区四区五区乱码| 欧美 亚洲 国产 日韩一| 午夜免费观看网址| 99久久国产精品久久久| 国产精品1区2区在线观看.| 日韩三级视频一区二区三区| 首页视频小说图片口味搜索| 免费无遮挡裸体视频| av有码第一页| 国内久久婷婷六月综合欲色啪| 男人舔女人的私密视频| 亚洲av熟女| 9191精品国产免费久久| 99在线人妻在线中文字幕| 最近最新中文字幕大全电影3| 国内精品一区二区在线观看| 免费高清视频大片| 成人国语在线视频| 一二三四在线观看免费中文在| 成人国产一区最新在线观看| 麻豆av在线久日| 看片在线看免费视频| 国产蜜桃级精品一区二区三区| 中国美女看黄片| 窝窝影院91人妻| 亚洲乱码一区二区免费版| 最近最新免费中文字幕在线| 天堂av国产一区二区熟女人妻 | 成在线人永久免费视频| 精品第一国产精品| 人人妻人人澡欧美一区二区| 日韩av在线大香蕉| 黄色a级毛片大全视频| 啦啦啦免费观看视频1| 国产成人影院久久av| 韩国av一区二区三区四区| 国产不卡一卡二| 成人av在线播放网站| 亚洲va日本ⅴa欧美va伊人久久| 欧美黄色片欧美黄色片| 亚洲欧美激情综合另类| 一边摸一边做爽爽视频免费| 亚洲精品国产精品久久久不卡| 99热6这里只有精品| 女同久久另类99精品国产91| 嫩草影院精品99| 日本三级黄在线观看| av中文乱码字幕在线| 91国产中文字幕| 天天一区二区日本电影三级| 久久久水蜜桃国产精品网| 国产久久久一区二区三区| 神马国产精品三级电影在线观看 | 国产探花在线观看一区二区| 成人三级黄色视频| 欧美成人一区二区免费高清观看 | 久久久久久久久中文| 亚洲激情在线av| 欧美日韩亚洲国产一区二区在线观看| ponron亚洲| 99riav亚洲国产免费| 在线十欧美十亚洲十日本专区| 90打野战视频偷拍视频| 亚洲第一欧美日韩一区二区三区| 老熟妇仑乱视频hdxx| 亚洲欧美日韩高清专用| 国产精品99久久99久久久不卡| 99国产综合亚洲精品| 亚洲专区字幕在线| 中文字幕熟女人妻在线| 免费在线观看日本一区| 日本精品一区二区三区蜜桃| 欧美另类亚洲清纯唯美| 亚洲精品一区av在线观看| 亚洲成人久久爱视频| 妹子高潮喷水视频| 女人爽到高潮嗷嗷叫在线视频| 天堂动漫精品| 色尼玛亚洲综合影院| 久久婷婷人人爽人人干人人爱| 国产高清videossex| 国产三级黄色录像| 免费在线观看视频国产中文字幕亚洲| 亚洲国产精品成人综合色| 一区二区三区激情视频| 美女 人体艺术 gogo| 两个人免费观看高清视频| 两个人看的免费小视频| or卡值多少钱| 久热爱精品视频在线9| 非洲黑人性xxxx精品又粗又长| 亚洲欧美日韩无卡精品| 级片在线观看| 国产一区二区三区在线臀色熟女| 成人国产综合亚洲| 黄片大片在线免费观看| 亚洲全国av大片| 久久久久国产一级毛片高清牌| 国产精品一区二区三区四区久久| 91九色精品人成在线观看| 久久亚洲真实| 身体一侧抽搐| 久久这里只有精品19| 国产精品香港三级国产av潘金莲| 99精品在免费线老司机午夜| 一个人免费在线观看电影 | 精华霜和精华液先用哪个| 黑人欧美特级aaaaaa片| 亚洲性夜色夜夜综合| 精品福利观看| 真人一进一出gif抽搐免费| 国产三级在线视频| 国产又黄又爽又无遮挡在线| 视频区欧美日本亚洲| 国产精品99久久99久久久不卡| 午夜老司机福利片| 国产精品久久久人人做人人爽| 男男h啪啪无遮挡| 老鸭窝网址在线观看| 日本免费一区二区三区高清不卡| 色尼玛亚洲综合影院| av有码第一页| 婷婷精品国产亚洲av| 老司机午夜十八禁免费视频| 亚洲激情在线av| 国产伦一二天堂av在线观看| 久久精品91无色码中文字幕| 亚洲全国av大片| 国产久久久一区二区三区| 中文字幕熟女人妻在线| 精品不卡国产一区二区三区| 免费搜索国产男女视频| 成人永久免费在线观看视频| 免费观看人在逋| 成年版毛片免费区| 国产精品久久视频播放| 999久久久精品免费观看国产| 久久香蕉激情| 亚洲 国产 在线| 免费在线观看亚洲国产| 亚洲乱码一区二区免费版| 久久久国产成人精品二区| www日本黄色视频网| √禁漫天堂资源中文www| 在线免费观看的www视频| 最新美女视频免费是黄的| 国产一区二区激情短视频| 首页视频小说图片口味搜索| 一二三四在线观看免费中文在| 俺也久久电影网| 免费在线观看影片大全网站| 欧美中文日本在线观看视频| 黄色 视频免费看| 国产麻豆成人av免费视频| 日韩 欧美 亚洲 中文字幕| 国产成人啪精品午夜网站| 岛国视频午夜一区免费看| 成人一区二区视频在线观看| 亚洲九九香蕉| 国产亚洲精品综合一区在线观看 | 91国产中文字幕| 啦啦啦韩国在线观看视频| 欧美性猛交黑人性爽| 特级一级黄色大片| 欧美成狂野欧美在线观看| 婷婷精品国产亚洲av在线| 99热这里只有精品一区 | 久久精品人妻少妇| 精品久久久久久成人av| 国产高清视频在线观看网站| 中文字幕av在线有码专区| 丝袜美腿诱惑在线| 欧美激情久久久久久爽电影| 欧美成人一区二区免费高清观看 | 国产又色又爽无遮挡免费看| 久久人妻av系列|