• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Effect of the amount of trapped particulate matter on diesel particulate filter regeneration performance using nonthermal plasma assisted by exhaust waste heat

    2020-01-10 07:40:52YunxiSHI施蘊(yùn)曦YixiCAI蔡憶昔XiaohuaLI李小華XiaoyuPU濮曉宇NanZHAO趙楠andWeikaiWANG王為凱
    Plasma Science and Technology 2020年1期

    Yunxi SHI (施蘊(yùn)曦), Yixi CAI (蔡憶昔), Xiaohua LI (李小華),Xiaoyu PU (濮曉宇), Nan ZHAO (趙楠) and Weikai WANG (王為凱)

    School of Automotive and Traffic Engineering, Jiangsu University, Zhenjiang 212013, People's Republic of China

    Abstract An experimental system of diesel particulate filter(DPF)regeneration using non-thermal plasma(NTP)technology assisted by exhaust waste heat was conducted and regeneration experiments of DPFs with different amounts of trapped particulate matter (PM) were conducted. The concentrations of the PM decomposition products(COx)and the internal temperature of the DPF were monitored to determine the performance of DPF regeneration and thermal safety of the NTP technology.The results showed that the concentrations of CO and CO2 and the mass of PM decomposition increased with the increase in the amount of captured PM, whereas the concentration of the NTP active substance(O3)escaping from the DPF decreased under the same working conditions of the NTP injection system.A higher amount of captured PM promoted the oxidative decomposition reaction between NTP and PM and improved the utilization rate of the NTP active substances. The peak temperature at the same measuring point inside the DPF generally increased and the phases of the peak temperature were delayed as the amount of captured PM increased. The temperature peaks and temperature gradients during the DPF regeneration process were far lower than the failure limit value, which indicates that NTP regeneration technology has good thermal durability and increases the service life of the DPF.

    Keywords: diesel, diesel particulate filter, regeneration, particulate matter, non-thermal plasma(Some figures may appear in colour only in the online journal)

    1. Introduction

    Diesel particulate filter (DPF) can effectively reduce the amount of particulate matter (PM) in the exhaust gas; it is installed in the exhaust system of a diesel engine and is considered the most effective after-treatment measure to reduce diesel PM emissions[1-3].The most common design structure of DPF is the wall-flow honeycomb structure,which has a large number of parallel small holes in the axial direction. In the adjacent filtering channels, one of the two ends is blocked. The exhaust flows through the wall of the DPF channel and flows out from the adjacent channel so that PM is deposited on the filter wall surface. However, the continuous deposition of particles will cause blockage of DPF, resulting in increased exhaust backpressure and increased fuel consumption.Accordingly, the timely removal of PM deposited in the DPF and DPF regeneration are key technologies [4, 5].

    The main DPF regeneration technologies include thermal regeneration[6,7],catalytic regeneration[8],and continuous regeneration [9]. The temperature of thermal regeneration is generally required to reach above 600°C, and the DPF regeneration process is prone to excessive thermal shock,leading to high energy consumption, high cost, and heat damage of the carrier structure. Catalytic regeneration can reduce the regeneration temperature of DPF to 200°C-400°C by coating the catalyst in DPF or doping the catalyst in the fuel. However, repeated coating and addition of catalyst are required, which complicates the operation and results in problems such as incomplete regeneration of DPF. Continuous regeneration is affected by the characteristics of the diesel oxidation catalyst,but it is influenced by the fuel spray characteristics, fuel injection pressure, fuel injection amount of the injector, and other factors. Therefore, the control strategy has high requirements. It is evident that the traditional regeneration methods have several disadvantages.

    Non-thermal plasma(NTP)technology has been adopted as a new method for the treatment of industrial pollutants and has broad application prospects in diesel after-treatment systems [10-13]. The NTP active substances are generated by gas discharge ionization, which activates chemical reactions that cannot be initiated under normal conditions. Huang et al[14]used an integrated NTP catalytic reactor to purify engine exhaust and discovered that NO2catalyzed the adsorption in the NTP generator and had a significant effect on the oxidation of the soluble organic fraction (SOF) components in the PM; the ionization process reduced the light-off temperature of the dry soot (DS) component. Yao et al [15-17] used a non-homogeneous dielectric barrier discharge (DBD) NTP generator to treat diesel PM emissions;when the gas gap was 0.4 mm and the power was 300 W, the NTP generator achieved a PM removal efficiency of 67%. Okubo et al[18-20] conducted the DPF online and offline regenerations by using an NTP generator with air and NO to simulate diesel exhaust. The results suggested that the concentration of CO and CO2increased after introducing the NTP active substance; sixty percent of NO2was converted to NO and the regeneration of DPF was achieved below 300°C. Kuwahara et al [21, 22] used indirect plasma technology to conduct a DPF regeneration test on a marine diesel engine.The exhaust passing through the DPF was about 3%-5% of the total exhaust of the engine. The results proved that continuous regeneration could be achieved and the renewable energy consumption was 5% of the total electric power of the diesel engine. This research demonstrated that NTP technology can effectively decompose PM in the exhaust gas, reducing the regeneration temperature of the DPF significantly (≤300°C)without a catalyst. NTP technology provides a new research approach for DPF regeneration.

    NTP regeneration technology significantly reduces the regeneration temperature of the DPF but it is necessary for the external heating source to reach the DPF initial regeneration temperature. Furthermore, most researchers have conducted regeneration experiments of DPF through simulated gas or exhaust tributaries and these conditions are far removed from the practical applications of NTP technology.In our previous research, the DPF to be regenerated was placed into a thermostat which provided the heat needed to trigger the regeneration reaction of DPF [23-25]. In order to further simplify the device and promote the practical application of NTP regeneration technology,the exhaust waste heat of the engine was used to provide the heat needed for DPF regeneration reaction in this study. The exhaust temperature of the engine is usually above 350°C and the DPF internal temperature will rise due to heating by the high-temperature exhaust gas during the operation. The DPF gradually cools from a high-temperature state after the engine has stopped.The residual heat after the shutdown is used in NTP regeneration technology,which is conducive to saving energy, simplifying the device, and promoting the application of NTP regeneration technology.

    An experimental system of DPF regeneration using NTP assisted by waste heat exhaust was developed in this study.The self-heating of DPF was used as the heat source for DPF regeneration and regeneration tests of DPF with different amounts of captured PM were conducted.The concentrations of CO and CO2and the internal temperature in DPF were measured to determine the regeneration performance of DPF and thermal safety of the NTP regeneration technology. The results of this study provide an experimental and theoretical basis for the practical application of NTP regeneration technology.

    2. Test system and method

    2.1. PM trapping test

    Figure 1 shows the schematic diagram of the testing system for PM capture in DPF.A YD480 diesel engine was used;its main technical parameters are listed in table 1.

    At the beginning of the test,valve 1 was closed and valve 2 was opened. The diesel engine speed and load were adjusted to 2500 r min?1and 69 N m?1, respectively. After the water temperature and oil temperature were stable,valve 1 was opened and valve 2 was closed.The PM trapping test was performed on four clean DPFs with trapping times of 60 min,180 min, 300 min, and 420 min, respectively. The deposition rate of diesel PM was 4.17 g h?1. The DPF had a height of 144 mm, a diameter of 152 mm, and a hole density of 100 cpsi.

    Table 1.Parameters of YD480 diesel engine.

    2.2. DPF regeneration test

    Figure 2 shows the sketch map of the DPF regeneration test system, which included an NTP injection system and a DPF regeneration system. The NTP injection system was used to produce reactive species with strong oxidability,consisting of a DBD-type NTP reactor, an oxygen supply unit, a watercooled unit, and an electric parameter measurement system.The NTP reactor had a coaxial cylinder structure and the thickness of the discharge gap was 2 mm. A stainless seamless steel pipe with an outer diameter of 48 mm was used as the internal electrode. Wire mesh with 400 mm axial length wrapped over the outer wall of the quartz tube was adopted to be the external electrode. The water-cooled unit was used to lower the discharge area temperature of the NTP reactor, which was conducive to the stable and reliable operation of the reactor. The electric parameter measurement system consisted of an electron impactor (CTP-2000K,Nanjing Suman Electronics Co.) and a digital oscilloscope(TDS3034B, Tektronix Inc.). The electron impactor was adopted as the NTP power source and the oscilloscope was used to monitor the discharge conditions.The common circuit contained two voltage-dividing capacitors (C1= 47 pf,C2= 47 nf)and a capacitor(Cm= 0.47 μf)that were utilized to measure the charge transfer. The DPF regeneration system included an engine bench (listed in section 2.1), a DPF with PM deposits, an ozone analyzer (Mini-HiCon, IN USA Inc.)and a photon portable gas analyzer (Madur, Austria). There were 12 K-type thermocouples distributed in different coaxial and radial positions inside the DPF to determine the change in temperature inside the DPF.A schematic of the thermocouple locations inside the DPF is shown in figure 3.

    The engine was operated in a stable condition to ensure that the temperature at each measuring point inside the DPF reached 100°C[26].Then,the engine was turned off and the NTP active substance(mainly O3)was sprayed into the DPF.The DPF regeneration test lasted 150 min. The control valve of the oxygen cylinder was opened and the flow rate was maintained at 5 l min?1.The discharge voltage and frequency of the power source were kept at 17 kV and 7 kHz, respectively. The power was 95 W, as calculated from the Q-V Lissajous plot [27]. The concentrations of the regenerated products (CO and CO2) were monitored by the gas analyzer.The O3analyzer was used to monitor the remaining O3concentration at the back end of the DPF regeneration process. The internal temperatures of the DPF and the concentrations of the residual O3were recorded every 5 min.

    2.3. Chemical reaction mechanism of DPF regeneration aided by NTP

    In this test,oxygen was used as an air source to pass into the NTP generator and the active substances O3and O with strong oxidation properties were generated through high voltage and high frequency discharge.The chemical reactions are shown as equations (1)-(3) [28-30]

    O3is formed via two main steps:the first step is shown in equations (1) and (2), where the oxygen molecules break the chemical bond to form atoms after discharge.The second step is the formation of O3via reactions between oxygen molecule radicals and ternary M, as shown in equation (3).

    Diesel PM is mainly composed of DS, the SOF and a small amount of inorganic salt [31, 32]. DS and SOF can be decomposed by the active materials produced by NTP reactor. The chemical reactions are shown as reaction as equations (4)-(9) [22, 33, 34]

    Equations (4) and (5) mean collision between active materials and SOF, where gaseous CO, CO2and H2O are generated. SOF attached to the surface of soot is stripped.Equations (6)-(8) mean collision between active materials and soot at the center of PM, where CO and CO2are generated. As is shown by equations (4)-(9), the main decomposition products of PM are CO and CO2.

    3. Results and discussion

    3.1. DPF regeneration products

    Figure 4 shows the concentrations of CO and CO2in the DPF regeneration process. DPF60, DPF180, DPF300, and DPF420represent DPFs with PM trapping times of 60 min, 180 min,300 min, and 420 min, respectively.

    In the initial regeneration test, the concentrations of CO and CO2increased sharply, indicating that once the NTP entered the DPF, the PM reacted with the active substance immediately.After the regeneration reaction had run for some time, the concentrations of CO and CO2leveled off, indicating that PM was continuously decomposed. The closer it was to the downstream of DPF, the more O3was consumed and the weaker the reaction with PM was; therefore, the PM region that was preferentially in contact with NTP reacted most strongly.Since the oxidation decomposition of PM is an exothermic reaction, once the temperature drops, it can be used as a sign of the completion of the reaction[35].Previous studies have shown that the temperature peaks of the axial measuring points occurred successively in the direction of airflow [36], which was also observed in this experiment (in figure 7),therefore the regeneration interface of the PM layer advanced from upstream to downstream. According to the trend of the CO and CO2concentrations (figure 4), the advancing speed of PM regeneration interface in this experiment was relatively stable.The amount of reactants and the contact time affect the oxidation decomposition rate of NTP and PM.The concentration and flow rate of NTP active substance entering the filters were constant in this tests;therefore, the amount of NTP and the contact time of NTP and PM were the same.The increase in the amount of trapped PM intensified the oxidative decomposition reaction inside the DPF, causing an increase in the concentration of CO and CO2. After 100 min, the concentrations of the decomposition product CO2of DPF60decreased. After 133 min of the regeneration test, the concentration of CO2decreased to 0,indicating that the PM deposited in the DPF60had been removed by oxidation. The CO2concentrations of DPF180,DPF300,and DPF420did not decrease in the later stage of the regeneration test, indicating that the internal regeneration reaction of the DPF was still ongoing.

    The removal quality of the PM in the DPF was calculated from the total amount of produced CO and CO2. The mass of C in the produced CO and CO2is an approximation of the mass of the removed PM and is calculated using equations (10)-(12)

    where m(C1)and m(C2)represent the masses of C in CO and CO2respectively; m(C12) represents the decomposition amount of PM;φ1and φ2represent the concentrations of CO and CO2respectively; qNis the volume flow rate of NTP,qN= 5 l min?1;Mcis the molar mass of C,Mc= 12 g mol?1;Vmis the molar volume of the gas, Vm= 22.4 l mol?1.

    Figure 5 shows m(C1),m(C2),and m(C12)of the DPF for different durations of PM capture. The mass of C2was significantly higher than that of C1, indicating that the main decomposition product of PM was CO2. The quality of the decomposed PM gradually increased with the increase in the PM trapping time. The regeneration times of the DPF experiments were the same (150 min); therefore, the reaction times of NTP and PM were the same. The concentration and total produced amount of the NTP active substances were almost identical under the same conditions of the NTP injection system. However, there was a significant difference in the COxconcentration of the DPF regeneration products and the removal mass of PM, indicating that the utilization rate of the NTP changed with the change in the amount of PM deposited in the DPF.

    The energy efficiency of the experiments can be calculated by equation (13).

    where α represents the energy efficiency;the m(C12)represents the decomposition amount of PM; P is the power of the NTP reactor, P = 95 W; t is the measuring time, t = 150 min =2.5 h.

    The energy efficiencies of DPF60, DPF180, DPF300and DPF420were 16.7 g kW?1h?1, 35.3 g kW?1h?1,40.9 g kW?1h?1and 43.9 g kW?1h?1respectively. The increase in the PM deposition in the DPF increased the energy efficiency in the DPF experiments.

    The concentration of residual O3versus time is shown in figure 6. The main active substance of the NTP with an oxygen source is O3[35]; the remaining O3concentration at the back end of the DPF indicates the degree of completion of the NTP and PM reaction. The initial O3concentration injected into the DPF measured was 35.2 mg l?1, this was much higher than that of the DPF backend, which indicated that NTP did play a role in PM decomposition.The oxidation decomposition of PM was an exothermic reaction[35].As the reaction progressed, the internal temperature of the reaction area inside DPF gradually increased.Although the amount of PM decreased, the high temperature was conducive to promoting the reaction between NTP and PM, which played a major role [36]. Therefore, the concentration of the residual O3decreased in the initial stage of regeneration.The remaining O3concentration was higher in the DPF60regeneration test. After 100 min, the O3concentration increased sharply and this phenomenon occurred at the same time as the rapid decrease in the CO2concentrations in the late stage of DPF60regeneration. These results indicated that the amount of PM that reacted with NTP decreased sharply and most of PM deposited in DPF had been oxidized and decomposed.The PM deposited in the DPF60was almost completely oxidized in the late stage of regeneration and the oxidation reaction was significantly reduced,leading to a rapid decrease in CO2concentrations but a large increase in the residual O3.The remaining O3concentration of the DPF300and DPF420regeneration was lower and the O3concentration continued to decrease as the regeneration test proceeded. The O3concentration of DPF420and DPF300decreased to 0 after 45 min and 60 min, respectively, which indicated that no O3escaped from the DPF backend and all the O3reacted with the PM.The remaining O3concentration decreased as the PM trapping amount increased. The results in figures 5 and 6 indicate that an increase in the PM deposition in the DPF significantly promotes the oxidative decomposition reaction of the NTP and PM and improves the utilization of the NTP active substances.Under the premise that the engine works normally, a delay in the time of DPF regeneration (increasing the PM capture amount) is beneficial to the optimization of the NTP regeneration technology.

    3.2. DPF internal temperature

    In the traditional regeneration process, the exothermic reaction inside the DPF may overheat local areas and cause damage to the filter (limit of service temperature: 1250°C) [37]. The common failure modes of DPF are hot melt failure and thermal stress failure. To evaluate the thermal safety of the NTP regeneration technology, the internal temperature change of the DPF during regeneration was monitored. Since the ambient temperature of the DPF was room temperature,more heat was dissipated closer to the outer wall. Therefore, the highest temperature during the regeneration process occurred near the central axis of the DPF.

    Figure 7 shows the temperature of the measuring point on the central axis of the DPF versus time. The internal temperature of the DPF increased and the decomposition of the PM was an exothermic reaction. Studies have shown that once the temperature of a certain measurement point drops,it indicates that the oxidation decomposition reaction of the PM at this location is almost complete and most of the deposited PM has been removed [36]. The temperature of each axial point of the DPF60and DPF180decreased after 95 min and 140 min respectively. The temperature of point 4a dropped below 70°C at the end of the DPF60regeneration test. After the regeneration test was stopped, the temperature measuring points of the DPF300and DPF420showed no temperature drop, indicating that the PM sediments in the DPF had not been completely removed. With the increase in the PMtrapping time, the rate of decrease in the temperature at each measurement point in the axial direction of the DPF decreased.Similar to the results shown in figures 4 and 6,the time when the temperature on the central axis of the DPF60dropped rapidly was the same time when the volume fraction of CO2decreased and the remaining O3concentration increased. Therefore, these phenomena can be used to evaluate the regeneration process of the DPF.

    Table 2.Peak temperatures of the DPF internal measuring points.

    Table 3.Time of peak temperatures of the DPF internal measuring points.

    Tables 2 and 3 respectively list the peak temperature and time of peak temperature of each measuring point in the DPF.It can be concluded that as the PM trapping amount increased,the peak temperature of the same measurement point inside the DPF showed an increasing trend and the time of the peak temperature exhibited a delay. The maximum values of the peak temperatures of the DPF60and DPF180occurred at measure point 3a and were 161.9°C and 205.0°C, respectively.Since the temperature measurement points of 1a and 4a were close to the inlet and outlet respectively of the NTP active material injection,the internal temperature of both ends of the DPF was lower than that of the middle section of the DPF. No temperature drop occurred at measuring point 4a in the DPF300but it was determined that the highest temperature of the DPF300regeneration was 207.6°C and occurred at measuring point 2a.A temperature decrease was not observed at the measuring points 3a and 4a in the DPF420but the highest temperature of the DPF420regeneration was 215.1°C which was higher than the highest temperature of the DPF300.It was observed that, with the increase in the amount of trapped PM, the internal maximum temperature of the DPF regeneration tended to increase.On the other hand,the results also indicate that the larger the amount of trapped PM, the more intense the internal reaction was,and the more heat was released. As shown in figure 5, the mass of the PM decomposed by NTP oxidation increased with the increase in the amount of trapped PM. Therefore, under the same regeneration conditions of the NTP injection system,a higher amount of trapped PM is conducive to promote the reaction between the NTP active substances and the PM.

    3.3. DPF internal temperature gradient

    During the regeneration process of the DPF, a large internal temperature difference will lead to different degrees of thermal expansion in certain areas and the thermal stress caused by the uneven thermal expansion will also lead to the fracture of the DPF carrier [38]. The average temperature gradient between two adjacent measuring points is represented by TG,which is calculated as follows:

    where Taand Tbrepresent the temperatures of the measuring point a and the measuring point b at a certain time respectively; Labrepresents the distance between the measuring point a and the measuring point b.

    The analysis of the internal temperature of the DPF regeneration and PM decomposition mass indicates that the internal oxidation decomposition reaction of the DPF420was the most violent. Figures 8 and 9 show the axial and radial temperature gradients respectively of the DPF420as a function of time. The maximum axial temperature gradient of the DPF420with the valve of 4.28°C cm?1occurred between measuring points 1a and 2a and the maximum radial temperature gradient with the valve of 1.78°C cm?1occurred between the measuring points 2b and 2c. The DPF is not damaged by thermal stress when the temperature gradient is less than 35°C cm?1[25]. The maximum internal temperature and temperature gradient of the DPF regeneration test were much lower than the failure limit.The NTP regeneration technology assisted by the exhaust waste heat endows the DPF with excellent thermal durability and increases the service life of the DPF.

    4. Conclusion

    A regeneration test of DPFs loaded with different amounts of PM was carried out using an NTP injection system assisted by exhaust waste heat. The regeneration performance and thermal safety of the NTP technology were investigated by monitoring the decomposition products(COx)of the PM and the internal temperature of the DPF. The conclusions are as follows:

    (1) The concentration of the PM decomposition products CO and CO2increased and the removal quality of the PM inside the DPF increased as the amount of trapped PM increased.The decomposition product CO2was the key factor to determine the removal amount of PM.

    (2) The concentration of the remaining O3after DPF regeneration decreased as the amount of trapped PM increased. The oxidative decomposition reaction of the PM deposited in the DPF and the NTP active substances was promoted by a higher amount of trapped PM and the utilization ratio of the NTP active substances was improved.

    (3) The peak temperature at the same measuring point inside the DPF generally increased and the phases of the peak temperature were delayed as the amount of trapped PM increased.

    (4) Both the peak temperature and temperature gradient during regeneration were lower than the DPF failure limit. The NTP regeneration assisted by exhaust waste heat exhibited good thermal durability,which increases the service life of the DPF.

    Acknowledgments

    This work is currently supported by National Natural Science Foundation of China (Nos. 51806085, 51676089), China Postdoctoral Science Foundation (No. 2018M642175),Jiangsu Planned Projects for Postdoctoral Research Fund(No.2018K101C) and Jiangsu University Youth Talent Cultivation Program Funded Project.

    亚洲熟女毛片儿| 搡老乐熟女国产| 美女 人体艺术 gogo| 18禁裸乳无遮挡免费网站照片 | 十八禁人妻一区二区| 日日干狠狠操夜夜爽| 99国产精品一区二区蜜桃av| 久久人妻熟女aⅴ| 日韩av在线大香蕉| 免费搜索国产男女视频| 国产一区二区三区在线臀色熟女 | 欧美大码av| 久久国产亚洲av麻豆专区| 一级毛片女人18水好多| 日韩大尺度精品在线看网址 | 国产片内射在线| 久久久久久久久免费视频了| 一级毛片高清免费大全| 免费在线观看日本一区| 国产免费男女视频| 国产无遮挡羞羞视频在线观看| 亚洲精品在线观看二区| avwww免费| 国产精品爽爽va在线观看网站 | 精品久久久精品久久久| 亚洲 欧美 日韩 在线 免费| 午夜精品国产一区二区电影| 亚洲伊人色综图| 欧美在线黄色| 国产三级黄色录像| 满18在线观看网站| 69精品国产乱码久久久| 日本wwww免费看| 亚洲欧洲精品一区二区精品久久久| 怎么达到女性高潮| 超碰成人久久| 国产精品免费视频内射| 亚洲精品在线观看二区| 国产精品一区二区三区四区久久 | 精品无人区乱码1区二区| 国产97色在线日韩免费| 亚洲精品国产色婷婷电影| 精品高清国产在线一区| www日本在线高清视频| 99久久99久久久精品蜜桃| 手机成人av网站| 动漫黄色视频在线观看| 欧美日本亚洲视频在线播放| 黑人巨大精品欧美一区二区蜜桃| 亚洲美女黄片视频| 男女做爰动态图高潮gif福利片 | 一边摸一边抽搐一进一出视频| 日日夜夜操网爽| 国产亚洲精品一区二区www| 亚洲自偷自拍图片 自拍| 妹子高潮喷水视频| 国产成人系列免费观看| 人人妻人人爽人人添夜夜欢视频| 中文字幕另类日韩欧美亚洲嫩草| 免费看十八禁软件| 97超级碰碰碰精品色视频在线观看| 精品日产1卡2卡| 久久久久久久久免费视频了| 国产免费男女视频| 久久婷婷成人综合色麻豆| 亚洲欧美日韩无卡精品| 日本精品一区二区三区蜜桃| 国产精品日韩av在线免费观看 | 亚洲一码二码三码区别大吗| 国产精品久久久久久人妻精品电影| 男人操女人黄网站| 国产精品 欧美亚洲| 无限看片的www在线观看| 国产一区二区三区视频了| 精品久久久精品久久久| 久久精品91蜜桃| 天天影视国产精品| 琪琪午夜伦伦电影理论片6080| 大香蕉久久成人网| 99久久综合精品五月天人人| 可以在线观看毛片的网站| 久久久久国产精品人妻aⅴ院| 嫩草影视91久久| 久久欧美精品欧美久久欧美| 99精品欧美一区二区三区四区| 亚洲av电影在线进入| 久久精品人人爽人人爽视色| 波多野结衣一区麻豆| 高清在线国产一区| 成人永久免费在线观看视频| 大型黄色视频在线免费观看| 国产成人系列免费观看| 1024香蕉在线观看| 黄色视频,在线免费观看| 欧美色视频一区免费| 国产精品久久电影中文字幕| 精品高清国产在线一区| 一区二区三区激情视频| 国产一区在线观看成人免费| 一二三四社区在线视频社区8| 最近最新中文字幕大全免费视频| 欧美日韩一级在线毛片| 法律面前人人平等表现在哪些方面| 99久久99久久久精品蜜桃| 国产99白浆流出| 久久亚洲精品不卡| 欧美日韩乱码在线| 久9热在线精品视频| 精品久久久久久成人av| 久久久久久久久免费视频了| 两性午夜刺激爽爽歪歪视频在线观看 | 国产精品 国内视频| 亚洲精华国产精华精| 国产精品久久视频播放| 大香蕉久久成人网| 国产欧美日韩综合在线一区二区| 无人区码免费观看不卡| 国产aⅴ精品一区二区三区波| 色综合婷婷激情| 亚洲熟女毛片儿| 男女下面进入的视频免费午夜 | 亚洲精品国产一区二区精华液| 精品高清国产在线一区| 国产精品一区二区精品视频观看| 亚洲精品一区av在线观看| 欧美激情 高清一区二区三区| 大型av网站在线播放| 国产麻豆69| 国产成人啪精品午夜网站| 一区二区三区国产精品乱码| 欧美亚洲日本最大视频资源| 丰满的人妻完整版| 中文字幕人妻丝袜制服| 黄色片一级片一级黄色片| 9色porny在线观看| 久久久久久久久中文| 亚洲中文字幕日韩| 国产蜜桃级精品一区二区三区| 亚洲一码二码三码区别大吗| 成年人黄色毛片网站| 欧美大码av| 嫁个100分男人电影在线观看| 国产成人精品在线电影| 亚洲精品中文字幕一二三四区| 人人妻人人澡人人看| 淫妇啪啪啪对白视频| 成年版毛片免费区| 在线视频色国产色| 久久久国产精品麻豆| 午夜福利在线免费观看网站| 桃红色精品国产亚洲av| 夫妻午夜视频| 日韩国内少妇激情av| 午夜免费成人在线视频| www.999成人在线观看| 啪啪无遮挡十八禁网站| 精品一区二区三区四区五区乱码| 欧美最黄视频在线播放免费 | 97超级碰碰碰精品色视频在线观看| 国产精品永久免费网站| 成年版毛片免费区| 国产真人三级小视频在线观看| 亚洲人成77777在线视频| 久久午夜亚洲精品久久| 多毛熟女@视频| 亚洲午夜精品一区,二区,三区| 村上凉子中文字幕在线| 中文字幕人妻丝袜一区二区| 亚洲欧美一区二区三区黑人| 免费在线观看黄色视频的| 9色porny在线观看| 一级黄色大片毛片| 成人三级黄色视频| 黑丝袜美女国产一区| 欧美色视频一区免费| 成人18禁在线播放| 一本大道久久a久久精品| 久久久国产欧美日韩av| 女性生殖器流出的白浆| 制服诱惑二区| 国产高清国产精品国产三级| 成年版毛片免费区| 国产精品香港三级国产av潘金莲| 亚洲欧美一区二区三区黑人| 日本vs欧美在线观看视频| 热re99久久国产66热| 午夜视频精品福利| 亚洲熟妇熟女久久| 国产色视频综合| 国产精品一区二区在线不卡| 国产精品久久久久成人av| 精品电影一区二区在线| 99热只有精品国产| 交换朋友夫妻互换小说| 国产麻豆69| 免费一级毛片在线播放高清视频 | 不卡一级毛片| 亚洲男人天堂网一区| 91国产中文字幕| 成人18禁高潮啪啪吃奶动态图| 又紧又爽又黄一区二区| 亚洲国产看品久久| 91av网站免费观看| 日本wwww免费看| 男男h啪啪无遮挡| 久久人人97超碰香蕉20202| 在线永久观看黄色视频| 69av精品久久久久久| 久久久久国产一级毛片高清牌| 国产亚洲精品综合一区在线观看 | 亚洲视频免费观看视频| 人成视频在线观看免费观看| 成年女人毛片免费观看观看9| 亚洲午夜理论影院| 纯流量卡能插随身wifi吗| 亚洲av成人av| 午夜精品久久久久久毛片777| 国产在线精品亚洲第一网站| 亚洲欧美日韩另类电影网站| 午夜福利一区二区在线看| 大型av网站在线播放| 色婷婷av一区二区三区视频| 国产高清videossex| 丝袜美足系列| 神马国产精品三级电影在线观看 | 香蕉国产在线看| 人妻丰满熟妇av一区二区三区| 精品少妇一区二区三区视频日本电影| 黄色女人牲交| 亚洲九九香蕉| 欧美丝袜亚洲另类 | 午夜影院日韩av| 国产一区二区三区综合在线观看| 真人一进一出gif抽搐免费| 久久青草综合色| 国产一区二区三区视频了| 久久精品影院6| 母亲3免费完整高清在线观看| 日韩欧美在线二视频| 一级a爱视频在线免费观看| 一进一出好大好爽视频| 老鸭窝网址在线观看| 国产av一区在线观看免费| 精品卡一卡二卡四卡免费| 国产欧美日韩一区二区三区在线| 成人免费观看视频高清| 99香蕉大伊视频| 日日爽夜夜爽网站| 老汉色∧v一级毛片| 久久中文看片网| 青草久久国产| 久久久久久久久免费视频了| 精品国产亚洲在线| 亚洲精品美女久久久久99蜜臀| 亚洲五月婷婷丁香| 自线自在国产av| 成人国产一区最新在线观看| 亚洲九九香蕉| 老司机福利观看| 侵犯人妻中文字幕一二三四区| 国产蜜桃级精品一区二区三区| 成人手机av| 精品国产乱子伦一区二区三区| 国产欧美日韩一区二区三区在线| 国产精品九九99| x7x7x7水蜜桃| 欧美乱码精品一区二区三区| 欧美日本亚洲视频在线播放| 美女高潮到喷水免费观看| 亚洲欧美激情综合另类| 欧美精品啪啪一区二区三区| 天天影视国产精品| 色精品久久人妻99蜜桃| 成人18禁高潮啪啪吃奶动态图| 久久久久久人人人人人| 精品久久久久久久毛片微露脸| av片东京热男人的天堂| 好看av亚洲va欧美ⅴa在| 亚洲精品一区av在线观看| cao死你这个sao货| 久久久久精品国产欧美久久久| 麻豆成人av在线观看| 99国产精品免费福利视频| 久久久精品国产亚洲av高清涩受| 国产免费男女视频| 国产主播在线观看一区二区| 十八禁人妻一区二区| 亚洲 欧美一区二区三区| 国产精品影院久久| 亚洲国产精品一区二区三区在线| 久久久国产一区二区| 国产精品亚洲一级av第二区| 欧美黄色片欧美黄色片| 亚洲人成电影免费在线| 精品国产国语对白av| av在线播放免费不卡| 免费看十八禁软件| 人妻丰满熟妇av一区二区三区| 韩国精品一区二区三区| 日日干狠狠操夜夜爽| 国产高清国产精品国产三级| 亚洲精品国产区一区二| 久久久久久大精品| 欧美丝袜亚洲另类 | 欧美激情极品国产一区二区三区| 99在线人妻在线中文字幕| 日韩有码中文字幕| 久久精品亚洲精品国产色婷小说| 一a级毛片在线观看| 成年人黄色毛片网站| 男男h啪啪无遮挡| 亚洲国产精品sss在线观看 | 免费av中文字幕在线| 精品一区二区三区视频在线观看免费 | 一区福利在线观看| 香蕉国产在线看| 色播在线永久视频| 美女大奶头视频| 老鸭窝网址在线观看| 欧美最黄视频在线播放免费 | 90打野战视频偷拍视频| 大码成人一级视频| 国产亚洲av高清不卡| 欧美日韩中文字幕国产精品一区二区三区 | 国产精品香港三级国产av潘金莲| 国产精品偷伦视频观看了| 99久久99久久久精品蜜桃| 亚洲片人在线观看| 国产av又大| 国产熟女xx| 丰满的人妻完整版| 欧美日韩福利视频一区二区| 中文字幕精品免费在线观看视频| 丰满的人妻完整版| bbb黄色大片| 免费在线观看视频国产中文字幕亚洲| av视频免费观看在线观看| 波多野结衣一区麻豆| 午夜91福利影院| 91麻豆精品激情在线观看国产 | 色哟哟哟哟哟哟| 91av网站免费观看| 黑人欧美特级aaaaaa片| 国产精品影院久久| 18美女黄网站色大片免费观看| 一级毛片高清免费大全| 久久亚洲精品不卡| 欧美色视频一区免费| 欧美精品啪啪一区二区三区| 亚洲激情在线av| 免费搜索国产男女视频| 欧美久久黑人一区二区| 变态另类成人亚洲欧美熟女 | avwww免费| 香蕉国产在线看| 在线十欧美十亚洲十日本专区| 黄片小视频在线播放| 免费在线观看亚洲国产| 在线观看66精品国产| 视频区欧美日本亚洲| 精品日产1卡2卡| 色哟哟哟哟哟哟| 国产成人精品久久二区二区91| 91老司机精品| 亚洲 国产 在线| 一夜夜www| 精品一区二区三区av网在线观看| 精品电影一区二区在线| 久久亚洲真实| 一区二区三区国产精品乱码| 少妇被粗大的猛进出69影院| 日韩有码中文字幕| 亚洲专区国产一区二区| 免费高清在线观看日韩| 成人影院久久| 国产野战对白在线观看| tocl精华| 岛国在线观看网站| 长腿黑丝高跟| 亚洲avbb在线观看| 97碰自拍视频| 又大又爽又粗| 精品高清国产在线一区| 少妇被粗大的猛进出69影院| 亚洲欧美激情综合另类| 一边摸一边做爽爽视频免费| 亚洲人成77777在线视频| 丰满迷人的少妇在线观看| 国产亚洲欧美98| 黑人操中国人逼视频| 日韩欧美三级三区| 色综合欧美亚洲国产小说| 91字幕亚洲| 中国美女看黄片| 一本综合久久免费| 人人妻人人爽人人添夜夜欢视频| 桃色一区二区三区在线观看| 热re99久久精品国产66热6| 一夜夜www| 国产精品野战在线观看 | 精品日产1卡2卡| 大型黄色视频在线免费观看| 母亲3免费完整高清在线观看| 亚洲午夜理论影院| 亚洲,欧美精品.| 国产亚洲欧美精品永久| 日韩欧美国产一区二区入口| 在线观看免费日韩欧美大片| 国产免费男女视频| 成人免费观看视频高清| 如日韩欧美国产精品一区二区三区| 成人精品一区二区免费| 久久中文看片网| 亚洲欧美精品综合久久99| 亚洲专区中文字幕在线| a在线观看视频网站| 又黄又爽又免费观看的视频| 国产亚洲欧美在线一区二区| 多毛熟女@视频| 日韩成人在线观看一区二区三区| 欧美在线一区亚洲| 丝袜美足系列| 日本精品一区二区三区蜜桃| 欧美中文综合在线视频| 午夜免费成人在线视频| 午夜精品久久久久久毛片777| 国产精品一区二区精品视频观看| 亚洲人成77777在线视频| 淫妇啪啪啪对白视频| 国产av一区二区精品久久| 亚洲成国产人片在线观看| 自线自在国产av| 欧美成狂野欧美在线观看| 亚洲av五月六月丁香网| av在线天堂中文字幕 | 老熟妇仑乱视频hdxx| 亚洲国产欧美一区二区综合| 欧美乱码精品一区二区三区| 日本黄色日本黄色录像| 黄色丝袜av网址大全| 午夜福利欧美成人| 97超级碰碰碰精品色视频在线观看| 麻豆久久精品国产亚洲av | 在线观看免费视频日本深夜| 亚洲av熟女| 午夜日韩欧美国产| 欧美日本中文国产一区发布| av天堂久久9| 婷婷六月久久综合丁香| 亚洲欧美精品综合久久99| 亚洲伊人色综图| 亚洲一卡2卡3卡4卡5卡精品中文| 一边摸一边做爽爽视频免费| 老鸭窝网址在线观看| 欧美日韩瑟瑟在线播放| 免费高清在线观看日韩| 久久 成人 亚洲| 亚洲熟妇中文字幕五十中出 | 日韩欧美一区二区三区在线观看| 女人被狂操c到高潮| 99久久人妻综合| 69精品国产乱码久久久| 国产精品亚洲一级av第二区| 女生性感内裤真人,穿戴方法视频| 性欧美人与动物交配| 久久欧美精品欧美久久欧美| 欧美日韩一级在线毛片| 国产精品亚洲一级av第二区| 最近最新免费中文字幕在线| 色老头精品视频在线观看| 中文字幕另类日韩欧美亚洲嫩草| 久久 成人 亚洲| 日韩三级视频一区二区三区| 久久人人爽av亚洲精品天堂| 黄色女人牲交| 成人亚洲精品av一区二区 | 少妇的丰满在线观看| 神马国产精品三级电影在线观看 | 最近最新中文字幕大全电影3 | 国产成人啪精品午夜网站| 亚洲国产精品999在线| 两人在一起打扑克的视频| 久久欧美精品欧美久久欧美| 午夜精品久久久久久毛片777| 亚洲一区二区三区色噜噜 | 精品一区二区三区av网在线观看| 宅男免费午夜| 久久伊人香网站| 男女下面进入的视频免费午夜 | 亚洲人成网站在线播放欧美日韩| videosex国产| 高清av免费在线| 999久久久精品免费观看国产| 久久人妻熟女aⅴ| 亚洲专区字幕在线| 国产亚洲精品久久久久5区| 午夜91福利影院| 天天添夜夜摸| 男男h啪啪无遮挡| 91成年电影在线观看| 国产精品野战在线观看 | 免费久久久久久久精品成人欧美视频| 三上悠亚av全集在线观看| 一级,二级,三级黄色视频| 老熟妇乱子伦视频在线观看| 男女床上黄色一级片免费看| 亚洲情色 制服丝袜| 国产91精品成人一区二区三区| www.熟女人妻精品国产| 黄色女人牲交| 久久影院123| 亚洲,欧美精品.| 久久午夜综合久久蜜桃| 91麻豆精品激情在线观看国产 | 亚洲精品一二三| 国产日韩一区二区三区精品不卡| 亚洲精品久久成人aⅴ小说| 高清在线国产一区| 80岁老熟妇乱子伦牲交| 色尼玛亚洲综合影院| 久久精品国产清高在天天线| 久久国产精品人妻蜜桃| 欧美黑人欧美精品刺激| 人人妻人人添人人爽欧美一区卜| 亚洲久久久国产精品| 国产精品电影一区二区三区| 中文字幕人妻丝袜一区二区| 亚洲色图综合在线观看| 19禁男女啪啪无遮挡网站| 男男h啪啪无遮挡| 亚洲av电影在线进入| 日韩免费高清中文字幕av| 中文字幕人妻丝袜制服| 色婷婷久久久亚洲欧美| 69av精品久久久久久| 精品国产美女av久久久久小说| 国产精品秋霞免费鲁丝片| 久久人人精品亚洲av| 成人国语在线视频| 日韩精品免费视频一区二区三区| 亚洲欧美精品综合久久99| 国产在线观看jvid| 一级片'在线观看视频| 午夜福利一区二区在线看| 亚洲精品国产一区二区精华液| 日韩欧美一区视频在线观看| 国产aⅴ精品一区二区三区波| 99国产精品免费福利视频| 50天的宝宝边吃奶边哭怎么回事| 美女高潮喷水抽搐中文字幕| 国产99久久九九免费精品| 国产精品爽爽va在线观看网站 | 亚洲熟妇熟女久久| 在线国产一区二区在线| 日本免费a在线| 日韩国内少妇激情av| 久久久久久久精品吃奶| 在线观看66精品国产| 久久精品亚洲av国产电影网| 纯流量卡能插随身wifi吗| 久久久国产成人免费| 国产欧美日韩一区二区三区在线| 国产成人一区二区三区免费视频网站| 亚洲av成人不卡在线观看播放网| e午夜精品久久久久久久| 国产xxxxx性猛交| √禁漫天堂资源中文www| 在线免费观看的www视频| 脱女人内裤的视频| 国产高清激情床上av| 级片在线观看| 成年人免费黄色播放视频| 亚洲午夜理论影院| 国产成人精品久久二区二区91| 在线观看免费视频日本深夜| 香蕉国产在线看| 韩国精品一区二区三区| 在线av久久热| 国产av一区二区精品久久| 精品一区二区三区av网在线观看| 亚洲中文av在线| 超碰成人久久| 国产av精品麻豆| 欧美精品亚洲一区二区| 国产精品成人在线| 日韩欧美国产一区二区入口| 色综合欧美亚洲国产小说| 亚洲成人国产一区在线观看| 亚洲欧美日韩高清在线视频| 国产成人精品在线电影| www日本在线高清视频| 丝袜人妻中文字幕| 午夜视频精品福利| 国产精品亚洲av一区麻豆| 精品人妻在线不人妻| 黄色怎么调成土黄色| 大陆偷拍与自拍| 国产精品98久久久久久宅男小说| tocl精华| 国产三级在线视频| 午夜成年电影在线免费观看| 一二三四社区在线视频社区8| 国产熟女xx| 啪啪无遮挡十八禁网站| 精品国产亚洲在线| aaaaa片日本免费| avwww免费| 国产激情欧美一区二区| 国产精品av久久久久免费| 亚洲精品一卡2卡三卡4卡5卡| 99热国产这里只有精品6| 久久国产精品男人的天堂亚洲| av天堂久久9| 黄色视频,在线免费观看| 少妇 在线观看|