PANG Ye-zhen,YU Xiao-li,ZHANG Xiao-wei,YU Meng-sa

(National Key Laboratory on Ship Vibration&Noise,China Ship Scientific Research Center,Wuxi 214082,China)

Measuring the Acoustic Properties of Underwater Coating Material under Pressure-Acoustic Impedance Method

PANG Ye-zhen,YU Xiao-li,ZHANG Xiao-wei,YU Meng-sa

(National Key Laboratory on Ship Vibration&Noise,China Ship Scientific Research Center,Wuxi 214082,China)

A method to measure the acoustic properties of underwater acoustic coating material under pressure based on acoustic impedance matrix is setup.Acoustic impedance matrix is measured to evaluate the absorption and transmission loss of underwater material.The test apparatus are well designed,especially for the tube,driver,backing mass and hydrophones.Isotropic material samples are tested to verify the test apparatus.Impedance matrix of acoustic coating material samples is measured to evaluate the absorption and transmission loss of samples,compared with theoretical results, and hence the acoustic impedance method is verified.

acoustic impedance;sound absorption coefficients;sound transmission loss

0 Introduction

Chung and Blaser(1980)[1-3]developed transfer function method to measure the reflections, input impedance and transmission loss of materials in the air.Goodman(1985)[4]applied for patent using this method to measure the input impedance in water.Wilson(2003)[5-6]described the propagation in the impedance tube filled with water in detail,and use impedance tube to measure the reflections of water layer with bubbles.Tao and Seybert(2001)[7]reviewed three kinds of methods to measure the transmission loss in pipe using transfer function method.

A new method to measure the impedance matrix is developed in these years.Impedance matrix is the unchanged parameter of acoustic material.The impedance matrix could be used to evaluate the acoustic properties with different backings,and it is a more efficient way than measuring the absorption coefficients or transmission loss directly.To measure the acoustic properties of underwater material,Cole and Martini(1994)[8]from Cambridge Acoustical Associates(USA)designed new acoustic impedance tube,PZT-8 piezoelectric rings and a beryllium piston are composed to be a low-frequency driver,transfer function of sound pressure in the tube and vibration of piston are measured to analyze the impedance matrix.Krylov Insti-tute developed the impedance tube to measure the acoustic properties of pipe parts.Akoum and Ville(1998)[9]used Fourier-Lommel transform to develop acoustic impedance test method in the tube.Reflections of plane-wave(0 order)and high-order modes could be analyzed by separating the incidence and reflection wave.Dalmont(2001)[10-11]converted the transfer matrix to impedance matrix.

1 Impedance matrix

1.1 Transfer matrix method

The acoustic material layer could be characterized as a two-port linear system(Fig.1) when the material layer is located in a water filled tube which could be treated as a plane wave sound field in low frequency.

Fig.1 Two-port model

where P1and P2are the sound pressure at input end and output end,V1and V2are the volume velocity at input end and output end,Z11and Z22are the input impedance at input end and output end,Z12and Z21are the transfer impedance at input end and output end,respectively.

The impedance parameters could be determined at special boundary conditions.

To ensure the volume velocity at output end V2=0,the output end should be absolutely rigid,which means that the inertial impedance of output end should be infinity.Practically backing mass made from steel is used to represent the inertial impedance.

1.2 Impedance matrix of isotropic material

For isotropic material sample,the input impedance and transfer impedance are determined by Eqs.(6-7)：

where HLis the thickness of sample,ρLis the density of sample,cLis the sound speed of sample.

1.3 Impedance matrix test method

The acoustic tube is shown in Fig.2,P1and P2are the sound pressure at input end and output end,V1and V2are the volume velocity at input end and output end.Two hydrophones are mounted on the wall of the tube,located at l and l+d before the input end to measure the sound pressure Pa1and Pa2,then the sound pressure P1and particle velocity V1of input end could be analyzed.The third hydrophone is mounted at the output end,just at the joints between sample and backing mass.The backing mass is treated as rigid backing,thus the particle velocity at output end V2≈0.

Fig.2 Scheme of acoustic test apparatus

where ρωcωis the characteristic impedance of water.

Thus the pressure and particle velocity at location l could be：

The pressure and particle velocity at location l+d could be：

From Eqs.(12-13),the amplitudes of injective sound and reflective sound,i.e.A and Bcould be solved,thus the sound pressure P1and particle velocity V1at input end are easily obtained,thus the input impedance is：

The transfer impedance is

where H1=Pa2/Pa1,H2=Pa3/Pa1.

2 Apparatus design

The apparatus(Fig.3)is based on an acoustic tube with the same diameter,the lower end is a sound driver which produces sound wave,and the upper end is the material sample and backing mass.The whole acoustic tube is filled with pressured water.

2.1 Tube

The whole tube is made from stainless steel,the diameter of tube is 120 mm,and the wall thickness of tube is 60 mm,first,the tube could be pressured more than 6 MPa,second, the tube is rigid enough to make sure the plane wave exist(Fig.4).

Fig.3 Acoustic impedance test apparatus

Fig.4 Sound speed of plane wave(0-order wave)

To seal the water from air,O-rings are used at both the driver and the top cover.Hydraulic connection locates at the lower part of the tube to fill water,pneumatic connection locates at the top cover to release the gas.

2.2 Driver

A long tonpilz driver(Fig.5)comprised by PZT rings is designed to get wide-band sound power in the tube.The injection sound pressure level is larger than 110 dB in 100-2 000 Hz,and the SNR is more than 20 dB.The driver could be working under the pressure 7 MPa.The driver and the tube are sealed with 2 O-rings.

Fig.5 The scheme figure and photo of driver

2.3 Backing mass

Generally,if the input impedance of backing mass(Fig.6)is ten times larger than the characteristic impedance of water,the backing mass could be treated as rigid backing.The thickness of the whole backing mass is 490 mm,the theoretically input impedance at 600-5 000 Hz is larger than 10 times of characteristic impedance of water,which is verified by using test under several pressure up to 3 MPa(Fig.7).

Fig.6 Steel backing mass

The input impedance of steel mass backing has a very little change with the change of environmental pressure.Because the characteristic impedance changes very little with pressure, so the effect of pressure on measurement system could be negligible.

2.4 Hydrophones

To limit the measurement uncertainty of transfer function,the distance of two hydrophones should be 0.1π＜kd＜0.8π,where k is the wavenumber,d is hydrophone distance.So the applicable frequency is 0.05c/d＜f＜0.4c/d.Four hydrophones and three kinds of distances(0.05 m,0.12 m and 0.4 m)are used to cover the whole measurement frequency span 100 Hz～2 kHz.

Fig.7 Theoretical and measured input impedances of multilayer steel backing

Fig.8 Relationship between hydrophone distance d and usable frequency span

Tab.1 Usable frequency span

3 Using impedance matrix to evaluate the absorption and transmission loss of underwater material

3.1 Absorption parameters using impedance

It is not intuitive to evaluate the properties of acoustic material from the impedance matrix.Usually the sound absorption coefficients and sound transmission loss are used to evaluate the properties of acoustic material,which could be converted from impedance matrix.

Suppose the acoustic material is isotropic material,d is the thickness,characteristic impedance is ρc,the impedance coefficients is：

The surface impedance could be

where zbis the surface impedance of backing structure.

From the surface impedance,the reflection coefficients R is

Thus the sound absorption coefficients is

It is easy to know that,different backing corresponding to Zbwill bring different reflection coefficients.To evaluate the acoustic character of coating materials,the acoustic character should be taken into account.

3.2 Transmission loss parameters using impedance

The incident sound pressure piAand reflection sound pressure prAcould be obtained from the impedance matrix and the transmitted sound pressure pt(Fig.9).

Fig.9 The acoustic parameters of coating material

The sound transmission loss could be represented using impedance parameters.

4 Measurement results

4.1 Impedance matrix verification

To verify the method,two kinds of model made by isotropic material water and rubber are measured.The typical impedance matrix of water and rubber could be analyzed using their characteristic impedance.

The water models with three kinds of thickness 50 mm,100 mm and 200 mm,the rubber model with two kinds of thickness 50 mm and 200 mm,are tested(Fig.10).

The input impedance and transfer impedance of water layer(Fig.11)are highly in accordance with theoretical results above 500 Hz-1 kHz,below this frequency span,the test results go to bad because the backing mass is not rigid enough,the input impedance of backing mass does not meet the condition of‘rigid backing’(Figs.12-13).

When the water layer becomes thicker,the lower end of effective frequency span gets lower,the reason is that when the water layer becomes thicker,the phase shift induced by thetransmission in the water gets bigger,the relative measurement error induced by the phase error of test system gets smaller,thus the frequency becomes effective in lower frequency span.

Fig.10 Measured input impedance of water

Fig.11 Measured transfer impedance of water

Fig.12 Theoretical and measured input impedance of rubber sample(50 mm thickness)

Fig.13 Theoretical and measured transfer impedance of rubber sample(50 mm thickness)

The impedance matrix of rubber sample(50 mm thickness)is measured,compared with theoretical impedance,they are well in accordance upon 800 Hz.

4.2 Absorption parameters verification

Using measured impedance matrix of rubber sample to calculate the sound absorption coefficients of rubber sample with steel backing,compared with the directly measured sound absorption coefficients.Measured and converted SAC are highly in accordance,the difference is less than 0.1 from 100 Hz to 5 kHz,and averaging error is less than 5%.

4.3 Transmission loss parameters verification

Water is acoustic transparent,the theoretical transmission loss for acoustic layer is 0 dB. The measurement results show that transmission loss for 10 cm thickness varies between-2 dB to 4 dB from 400 Hz to 5 kHz,especially,the measurement results are less than 1dB different from theoretical results from 2 000 Hz to 5 000 Hz.High pressure bring better results, the measurement results at 3 MPa have much less error than atmosphere.

Fig.14 Measurement results and converted results of incident absorption coefficients

Fig.15 The measurement transmission loss for 10 cm thickness water layer

5 Conclusions

A method to measure the properties of underwater acoustic material under pressure based on acoustic impedance matrix is setup.Acoustic impedance matrix is measured to evaluate the absorption and transmission loss of underwater material.The test apparatus are well designed, especially for the tube,driver,backing mass and hydrophones.Isotropic material samples are tested to verify the test apparatus.Impedance matrix of acoustic coating material samples are measured to evaluate the absorption and transmission loss of samples,compared with theoretical results,the acoustic impedance method is verified.The impedance matrix could be used to evaluate the acoustic properties with different backings,it is a more efficient way than measuring the absorption coefficients or transmission loss directly.

[1]Chung J Y,Blaser D A.Transfer function method of measuring in-duct acoustic properties.I.Theory[J].JASA,1980,68 (3)：907-913.

[2]Chung J Y,Blaser D A.Transfer function method of measuring in-duct acoustic properties.II.Experiment[J].JASA,1980, 68(3)：914-921.

[3]Chung J Y,Blaser D A.Transfer function method of measuring acoustic intensity in a duct system with flow[J].JASA, 1980,68(6)：1570-1577.

[4]Goodman J,43.30.Ky,43.85.Bh Underwater acoustic impedance measuring apparatus[P].Patent Number：4638275,1985. [5]Wilson P S.Sound propagation and scattering in bubbly liquids[D].Doctoral Dissertation,Boston University,2003.

[6]Wilson P S,Roy R A,Carey W M.An improved water-filled impedance tube[J].J Acoust.Soc.Am.,2003,113(6)：3245-3252.

[7]Tao Z,Sybert A F.A Review of current techniques for measuring muffler transmission loss[C].SAE Noise and Vibration Conference,2003.

[8]John E Cole,Kyle Martini.A device for measuring the properties of acoustic materials at low frequency under pressure [R].AD Report,1994.

[9]Akoum M,Ville J M.Measurement of the reflection matrix of a discontinuity in a duct[J].J Acoust.Soc.Am.,1998,103 (5)：2463-2468.

[10]Dalmont J P.Acoustic impedance measurement,Part I：A review[J].Journal of Sound and Vibration,2001,243(3)：427-439.

[11]Dalmont J P.Acoustic impedance measurement,Part II：A new calibration method[J].Journal of Sound and Vibration, 2001,243(3)：441-459.

《船舶力學》稿約須知

一、《船舶力學》（月刊）是中國船舶科學研究中心和中國造船工程學會聯合主辦的國內外公開發行的專業性學術期刊。它以繁榮科技文化，培養科研人才，促進科學技術向生產力轉化，為社會主義現代化建設服務為宗旨。本刊著重刊登我國船舶與海洋工程力學界的科學著作、學術論文和創新研究成果以及有關振動與噪聲、計算機應用、測試技術和研究綜述等，是我國船舶與海洋工程力學界廣大學者和中青年科技工作者的一個重要學術園地和論壇。本刊為中文核心期刊；中國科技核心期刊；RCCSE中國核心學術期刊；美國《工程索引》Ei核心期刊。2014年被評為中國精品科技期刊和百種中國杰出學術期刊。本刊同時刊登中、英文論文。歡迎國內外讀者踴躍撰搞。

二、稿約要求

1.論點明確、條理清晰、文字簡煉、論據充分、數據可靠。學術論文和綜述文章一般不超過6000字（包括圖、表）；

2.歡迎使用打印稿（用A4紙單面打印，打印一式兩份），如用網上投稿也應附有打印稿，標點準確，不要使用非正式公布的簡化漢字。如用網上投稿，郵件發至：huanggr@cssrc.com.cn，同時郵寄二份打印稿以便與電子郵件發送稿校核；

3.計量單位一律采用《中華人民共和國法定計量單位》；

4.來稿要求附有中、英文摘要，中、英文關鍵詞（Key words）3～8個，并放在論文首頁。英文論文稿末頁應附有中文題目、中文摘要及關鍵詞；

5.請?zhí)峁┣逦鷾蚀_的圖、表。圖中文字不宜太多。圖題和表頭應同時使用中英文表示。英文稿的圖應插入文中，不要集中放在論文最后；

6.參考文獻只選用最主要的、公開發表過的，并在文中引用處注明。為便于Ei收錄，中文參考文獻應附有英文翻譯。文后參考文獻按文中引用順序排序，著錄格式應符合：

（1）期刊[序號]作者.題名[J].刊名，年，卷（期）：起止頁碼.

（2）專著[序號]作者.題名[M].出版地：出版者，年，起止頁碼.

（3）學位論文[序號]作者.題名[D].出版地：出版者，年.起止頁碼.

（4）論文集[序號]作者.題名[C]//出版地：出版者，年.起止頁碼.

（5）論文集中析出文獻[序號]作者.析出文獻題名[C]//原文獻責任者.原文獻題名.出版地：出版者，出版年，起止頁碼.

（6）國家標準[序號]，標準編號，標準名稱[S].

（7）專利[序號]專利所有者.題名[P].國別：專利號，出版日期.

7.請在篇首頁地腳處寫明作者簡介，英文論文請用中、英文寫明（簡介應包括姓名、出生年、性別、籍貫、單位職稱和主要從事工作）；

8.請在篇首頁地腳處注明資助基金名稱的中英文全稱及基金號；9.請在來稿中注明聯系地址、電話（包括E-mail信箱）。

三、本刊已相繼加入國內外的一些重要數據庫，提供網絡信息服務。故凡向本刊投稿者，均視為其文稿刊登后可供國內外刊物或數據庫收錄、轉載并上網發行；其作者文章著作權使用費與稿酬一次付清，本刊不再另付其它報酬。凡有不同意者，請來函或來電聲明，本刊將作適當處理，或請另投它刊。

四、凡經《船舶力學》上刊出論文，其版式、版權屬于《船舶力學》編輯部，其他單位或個人不得侵權。

五、對錄用的稿件編輯部可作適當刪改或請作者刪改。對未錄用稿件編輯不退稿，請作者自行留底。

六、本刊發表學術論文文責（政治、學術、保密）作者自負，請勿一稿兩投。

七、論文發表后，請作者隨時將國內外的收錄、獲獎等信息告知編輯部。

加壓聲學覆蓋層聲學性能測試—聲阻抗方法

龐業珍，余曉麗，張曉偉，俞孟薩
（中國船舶科學研究中心船舶振動噪聲重點實驗室，江蘇無錫214082）

文章建立了一種基于聲阻抗傳遞矩陣方法的加壓聲學覆蓋層聲學性能測試方法。測量得到的聲阻抗矩陣用于計算聲學覆蓋層吸聲系數與隔聲量。對聲阻抗測試裝置包括聲管、聲源、背襯和水聽器布置等進行了詳細介紹。通過測量均勻材料樣品聲阻抗對測試裝置進行了驗證，通過測試聲學覆蓋層樣品計算吸聲系數與隔聲量，并與理論計算結果進行對比，對聲阻抗方法進行了試驗驗證。

聲阻抗；吸聲系數；隔聲量

TB56

：A

龐業珍（1982-），男，中國船舶科學研究中心博士研究生；

1007-7294（2017）03-0372-10

TB56

：A

10.3969/j.issn.1007-7294.2017.03.012

余曉麗（1980-），女，中國船舶科學研究中心高級工程師；

張曉偉（1987-），男，中國船舶科學研究中心工程師；

俞孟薩（1960-），男，中國船舶科學研究中心研究員，博士生導師。

Received date：2016-12-28

Foundation item：Supported by the National Key Research and Development Program of China(Grant No. 2016YFF0200900)

Biography：PANG Ye-zhen(1982-),female,Ph.D.student,E-mail：chaos123@qq.com;

YU Meng-sa(1960-),male,researcher,E-mail：yumengsa@sohu.com.