卜小峰

摘要：

根據質量作用定律，測定了銅膜在靜態腐蝕和化學機械拋光（Chemical Mechanical Polishing，CMP）兩種反應條件下的化學反應速率常數；通過Arrhenius方程，測定了銅膜在兩種反應條件下的化學反應活化能.結果表明：當拋光液溫度為298.15 K，工作壓力為13 780 Pa時，靜態腐蝕條件下體系化學反應速率常數是114.80 s-1，而CMP條件下體系的化學反應速率常數是412.11 s-1，同時，CMP條件下的反應活化能為4 849.80 J，靜態腐蝕條件下的反應活化能為31 870.30 J，由此得出，反應活化能的降低是CMP過程中的機械摩擦作用所致.因此，根據CMP過程中銅膜和拋光墊各自克服滑動摩擦力所作的系統功，推導出CMP過程中活化能降低值的系統功表達式，并通過改變工作壓力和轉速來驗證該表達式的適用性.

關鍵詞：

質量作用定律； Arrhenius方程； 化學反應； 活化能； 機械摩擦作用

中圖分類號： O 647； TN 43文獻標志碼： A

Abstract：

According to the law of mass action，the reaction rate constants of copper film chemical reaction are measured under static corrosion and dynamic chemical mechanical polishing （CMP） process.The activation energy of copper film chemical reaction is acquired under the two kinds of reaction conditions above mentioned based on the Arrhenius equation.The results show that：as the slurry temperature is 298.15 K with working pressure 13 780 Pa during the CMP process，and the chemicalreaction rate constant of the system under the static corrosion condition is 114.80 s-1，and the reaction activation energy is 31 870.30 J，while the reaction rate constant increases to 412.11 s-1 and reaction activation energy decreases to 4 849.80 J under the CMP condition.Thus，the mechanical friction effect in the CMP process causes the decline of activation energy as a result. Therefore，according to the system power produced by the sliding friction between the copper film and the polishing pad in the CMP process，system power expression used for describing the decline of activation energy in the CMP process is calculated. And also the applicability of the expression has been verified by changing the work pressure and speed of the CMP process.

Keywords：

law of mass action； Arrhenius equation； chemical reaction； activation energy； mechanical friction effect

化學機械拋光（Chemical Mechanical Polishing，CMP）技術是目前半導體行業的重要加工手段，是當前能夠?qū)崿F(xiàn)全局拋光的唯一實用技術.探索更加溫和且更容易實現銅膜凹凸速率差的CMP工藝成為影響微電子產業發展的關鍵因素.大量文獻證實，CMP過程中材料去除速率并非化學和機械作用的簡單線性相加，而是遠遠大于兩者單獨作用之和.若再考慮到凹處和凸處不同材料的去除環境，問題將會更加復雜[1-3].部分文獻[4-5]認為只要加入了BTA等一些腐蝕抑制劑，就能從根本上解決凹處速率快的問題，但并未考慮到由于機械摩擦作用而導致的鈍化膜脫落現象.也有部分文獻[6-7]認為，溫和的反應條件即大幅度削弱機械摩擦作用，有利于實現表面的拋光.因?yàn)樵诘蜋C(jī)械強度下，凹處所形成的鈍化膜難以脫落，而凸處的材料卻不斷被去除，由此循環往復，通過延長反應時間來最終實現銅布線表面的拋光.但其并未考慮到拋光效率等因素，無法滿足工業生產的需要[7].基于此現象，本文以摩擦化學反應活化能為切入點，通過質量作用定律探究了CMP過程和靜態腐蝕過程的化學反應活化能的差值，并通過Preston方程和Arrhenius方程分別對銅膜的凸處和凹處的材料去除機理進行研究.

4 結論

通過靜態腐蝕和CMP過程中銅離子的絡合反應，闡述了CMP過程中機械作用對化學反應的影響.揭示了CMP過程中機械摩擦與化學反應的協同作用機理，即CMP條件下速率提升的原因正是因?yàn)榛瘜W(xué)反應活化能的降低，降低的數值被系統機械摩擦所產生的內能所彌補，機械作用所帶來的最主要的效果是降低了化學反應的活化能，即提高了活化分子的數量.

參考文獻：

[1]OH S，SEOK J.An integrated material removal model for silicon dioxide layers in chemical mechanical polishing processes[J].Wear，2009，266（7/8）：839-849.

[2]TSAI T C，TSAO W C，LIN W，et al.CMP process development for the viamiddle 3D TSV applications at 28 nm technology node[J].Microeletronic Engineering，2012，92（3）：29-33.

[3]ZHENG J P，ROY D.Electrochemical examination of surface films formed during chemical mechanical planarization of copper in acetic acid and dodecyl sulfate solutions[J].Thin Solid Films，2009，517（16）：4587-4592.

[4]NG D，KULKARNI M，JOHNSON J.Oxidation and removal mechanisms during chemicalmechanical planarization[J].Wear，2007，263：1477-1483.

[5]PANDIJA S，ROY D，BABU S V.Achievement of high planarization efficiency in CMP of copper at a reduced down pressure[J].Microelectronic Engineering，2009，86：367-373.

[6]YANG J C，OH D W，LEE G W.Step height removal mechanism of chemical mechanical planarization（CMP） for subnanosurface finish[J].Wear，2010，268（3/4）：505-510.

[7]KRISTIN G，SHATTUC K，JENG Y L，et al.Characterization of phosphate electrolytes for use in Cu electrochemical mechanical planarization[J].Electrochemical Acta，2008，53：8211-8216.

[8]王同慶，韓桂全，趙德文，等.拋光墊特性及其對300 mm晶圓銅化學機械拋光效果的影響研究[J].摩擦學學報，2013，33（4）：394-399.

[9]NOH K，SAKA N，CHUN J H.Effect of slurry selectivity on dielectric erosion and copper dishing in copper chemicalmechanical polishing[J].CIRP AnnalsManufacturing Technology，2004，53（1）：463-466.

（編輯：丁紅藝）